AU
B16BA-00

DTC B16BA-00 indicates the Airbag Control Unit (SRS ECU) detected an abnormality during its internal self-check or lost normal function — Seal 6 EV

Safety System

DTC B16BA-00 indicates the Airbag Control Unit (SRS ECU) detected an abnormality during its internal self-check or lost normal function.

This fault indicates an SRS ECU hardware failure, software malfunction, power supply or communication interruption, or internal algorithm error, rather than an external sensor or actuator issue.

The SRS ECU serves as the core of the safety system and monitors the crash sensors, seat belt pretensioners, airbag ignition circuits, and occupant classification system.

This fault forces the entire airbag system into fail-safe mode; the system may fail to deploy the airbags and pretensioners during a collision.

The instrument cluster airbag warning light (AIRBAG/SRS light) remains illuminated, and some models trigger a buzzer alarm.

Due to the highly integrated SRS ECU in Qin series models (especially 2017-2018 models), related communication or internal fault codes in the B16B0-B16BF range may accompany this fault.

5
Cases Logged
5
Causes
Likely Causes — Seal 6 EV
  • 1SRS ECU internal processor or memory fault: Voltage fluctuations, component aging, or electrostatic breakdown damage the internal circuit board of the control module, preventing it from executing the deployment algorithm or storing crash data.
  • 2Power supply system fault: battery voltage too low (<9V) or too high (>16V), blown SRS dedicated fuse (typically in dashboard fuse box IF08 or engine compartment fuse box EF15), or poor contact at ECU ground wires G301/G302, causing ECU reset or unstable operation.
  • 3CAN communication bus fault: Short or open circuit in the power CAN or dedicated safety CAN lines between the SRS ECU, BCM, and instrument cluster (the instrument cluster wiring harness passing through the A-pillar junction on Qin series models is prone to wear), causing ECU communication loss.
  • 4External interference or liquid ingress: Water enters the ECU mounting location (usually under the center console or central tunnel) after vehicle wading, or high-power radio equipment disrupts the internal ECU capacitors and clock circuit.
  • 5Software version defect or data corruption: Early SRS software on 2017-2018 Qin models contains a logic flaw that triggers an internal watchdog reset under specific temperature or voltage conditions. Upgrade to software version V2.3 or higher.
What To Do
  • 1
    Initial diagnosis: Connect the VDS2000/3000 diagnostic tool to the vehicle OBD port. Read all SRS fault codes to confirm if B16BA-00 appears alone or with associated codes such as U0155 (lost communication with instrument cluster) and B16B1 (abnormal internal voltage). Record the voltage and temperature values from the freeze frame data.
  • 2
    Power supply and ground check: Disconnect the negative battery terminal, wait 3 minutes, and check the SRS ECU connector (16-pin or 24-pin, located under the center console; remove the passenger glove box or center armrest to access). Measure the voltage to ground at Pin 1 (constant B+) and Pin 8 (IG power); voltage must be 12V. Measure the resistance to ground at Pin 16/32 (ground); resistance must be <1Ω. Check if fuse IF08 (10A) is blown.
  • 3
    Communication line inspection: Reconnect the battery and turn the ignition switch to ON. Measure the voltage to ground for CAN-H (Pin 6) and CAN-L (Pin 14); voltages should be approximately 2.6V and 2.4V respectively. Resistance should measure 60Ω (the terminating resistor is inside the ECU). Check the wiring harness at the A-pillar and floor harness junction for wear or signs of water ingress.
  • 4
    ECU body inspection: Remove the SRS ECU (disconnect the battery first and wait at least 90 seconds to discharge the backup power supply). Check the housing for cracks, signs of water ingress, or a burnt smell. Check the connector terminals for oxidation or backed-out pins. For Qin series models specifically, check if a loose ECU mounting bracket is causing a poor connection.
  • 5
    Software update or replacement: If hardware checks are normal, use the diagnostic tool to perform 'SRS system software update'. Select the corresponding model (Qin EV300/450 or Qin 100) and year, then update to the latest version. If the update fails or hardware is damaged, replace the SRS ECU with a unit of the same part number (such as EF-3636100 or SA2E-3636100). Perform coding configuration and crash sensor calibration.
  • 6
    System verification and code clearing: After replacement or repair, clear all fault codes and perform the 'SRS System Self Test' (Special Function > SRS Self Test). Confirm B16BA-00 changes to a history code and no current codes exist. Simulate a crash test (use the diagnostic tool to perform the 'Crash Output Test') to check the resistance of each circuit (must be <2Ω) and insulation. Finally, perform a road test to confirm the airbag light turns off after the self-test.
Real-World Cases
BYD DTC AI Analysis

Qin EV300 airbag light comes on intermittently while driving, logs DTC B16BA-00.

✓
Vehicle: 2017 BYD Qin EV300, 82,000 km. Symptom: SRS warning light illuminated intermittently while driving. The light went out after shutting down and restarting. VDS read stored DTC B16BA-00. Diagnosis: Checked ECU power supply; Pin 1 voltage fluctuated between 11.2–13.8 V (should be stable 12 V). Traced the wiring and found a loose EF15 terminal in the engine compartment fuse box, causing power supply interruption to the SRS ECU on rough roads. Repair: Repaired the fuse box terminal, fitted a voltage stabiliser, and cleared the DTC. No recurrence after one month of monitoring.
BYD DTC AI Analysis

Qin 100 SRS system failed after wading, multiple DTCs present.

✓
Vehicle: 2017 BYD Qin 100. After wading through water during a heavy rainstorm, the instrument cluster displayed "Check Airbag System". DTCs: B16BA-00 (Current), B16B1 (Internal Fault), U0155 (Communication Fault). Diagnosis: Removed the centre console and found water stains on the SRS ECU housing. Disassembled the ECU and found corrosion and short circuit traces on the internal circuit board. Measured a short to ground on the CAN bus. Solution: Replaced the SRS ECU assembly (part number EF-3636100), dried the wiring harness, reapplied waterproof sealing, and performed system configuration and sensor calibration.
BYD DTC AI Analysis

Qin EV450: DTC B16BA-00 present after instrument cluster replacement, will not clear

✓
Vehicle: 2018 Qin EV450. The SRS warning light stayed on after replacing the instrument cluster at the dealership. Fault symptoms: Scan tool showed codes B16BA-00 and U0155 (lost communication with instrument cluster). Diagnosis: Checked the new instrument cluster part number against the old unit — they matched, but the configuration code differed. This prevented the SRS ECU from recognising the instrument cluster's safety authentication data. Solution: Accessed 'SRS System Configuration' using VDS, entered the correct vehicle VIN and configuration code (0x04 for the Qin EV450), and performed online matching. This resolved the fault.
BYD DTC AI Analysis

Voltage anomaly causing ECU internal restart fault in Qin 80

✓
Vehicle: 2017 BYD Qin 80. Frequent SRS faults occurred after installing a high-power aftermarket audio system. Symptoms: SRS warning light flashes at startup. Stored DTC B16BA-00 (internal voltage abnormal). Diagnosis: Battery voltage dropped to 8.5V during cranking and remained unstable even after adding a capacitor. Inspection found the audio system drew power directly from the SRS ECU constant power circuit, causing interference. Fix: Rewired the audio power feed to a dedicated fuse position and replaced the SRS ECU (internal voltage regulation module damaged). Fault permanently resolved.
BYD DTC AI Analysis

Outdated software version triggers false alarm on Qin EV300

✓
Vehicle: 2017 Qin EV300. No accident history, but the dashboard intermittently displays an airbag fault warning. Fault symptom: SRS warning light illuminates during cold start and extinguishes once warm. Fault code B16BA-00 is intermittent. Diagnosis: Checked the wiring harness and power supply – both normal. Checked the technical service bulletin and found certain 2017 production batches have a software defect causing ECU self-test timeout in low temperatures. Solution: Connected VDS and performed a software upgrade from V1.8 to V2.4, then executed 'SRS System Initialization'. Performed 20 cold start tests – no fault recurrence.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.