AU
B1741

DTC B1741 indicates the Airbag Control Module (ACM) detected a short to ground in the Left Rear Side Airbag squib circuit — Seal 6 EV

Safety System

DTC B1741 indicates the Airbag Control Module (ACM) detected a short to ground in the Left Rear Side Airbag squib circuit.

In the SRS system, two wires (high side and low side) connect each airbag inflator to the ACM.

These circuits normally maintain a high-impedance state.

The ACM logs a short to ground when it detects an abnormally low circuit resistance (close to 0Ω) or a voltage drop to ground potential.

This condition causes the following: 1) The airbag system enters fail-safe mode, disabling this airbag and related airbags. 2) The airbag warning light (SRS light) remains illuminated. 3) The airbag fails to deploy during a collision, severely compromising occupant safety. 4) The system may store related fault codes, such as B1740 (airbag not present).

Different vehicle models or model years may define B1741 as a left front window lift switch signal fault in the Left Body Domain Controller (LBDC) system, reflecting the evolution of BYD fault codes across electrical architectures.

The B1741 fault code on the Seal 6 EV indicates a high-severity short to ground in the left rear side airbag squib circuit. This can disable the airbag system and keep the SRS warning light on. Common causes include damaged wiring in the left rear door hinge area or water ingress and corrosion at the airbag connector. Visit an authorised dealer for diagnosis and repair. Typical repair cost data is available.
5
Cases Logged
5
Causes
Likely Causes — Seal 6 EV
  • 1Wiring harness mechanical damage: Repeated bending of the left rear door wiring harness at the door hinge wears and splits the insulation. The internal wire contacts the metal door frame, creating a short to ground.
  • 2Connector water ingress and corrosion: Poor sealing of the airbag connector inside the left rear door trim panel allows an electrolyte path to form between the pins or to ground after car washing, wading, or rainwater leakage, causing a short circuit.
  • 3Airbag module internal fault: Airbag assembly internal squib short circuit, or internal wiring shorted to the metal housing. Manufacturing defects or long-term high-temperature aging usually cause this fault.
  • 4Improper modification or repair damage: Fixing screws pierce the dedicated yellow SRS wiring harness when installing aftermarket ambient lighting, audio equipment, or window film, or tools accidentally crush the harness during door removal or installation.
  • 5ACM internal drive circuit fault: A damaged airbag control module internal monitoring circuit falsely reports a short circuit, or an internal power transistor breakdown causes an actual short circuit.
What To Do
  • 1
    Safety preparation and power isolation: Turn the vehicle OFF, disconnect the 12V battery negative terminal, and wait at least 90 seconds (120 seconds for some models) to allow the SRS capacitor to fully discharge and prevent accidental airbag deployment.
  • 2
    Visual and physical inspection: Remove the left rear door trim panel. Carefully inspect the yellow SRS wiring harness sleeve at the door hinge for damage. Check the airbag connector (usually located at the door-to-body connection or under the seat) for signs of water ingress, corrosion, or deformed pins.
  • 3
    Circuit continuity and insulation measurement: Disconnect the ACM and left rear side airbag connectors. Use a multimeter to measure the resistance from the airbag-side wiring harness to body ground; the normal value must be greater than 1 MΩ. Measure continuity at both ends of the wiring harness and confirm no short to ground. Check the insulation resistance between the wiring harness and body GND.
  • 4
    Component replacement verification: Replace the original airbag module with a known-good airbag simulator (2Ω resistor) or bridge with a known-good wiring harness. Clear the fault code, power on, and read the data stream. Observe if the fault code transfers or disappears to determine whether the issue is a wiring harness fault, a connector fault, or an internal short circuit in the airbag module.
  • 5
    Targeted repair or replacement: If the wiring harness has a short circuit, repair the damaged section with heat-shrink tubing and rewrap it, then adjust the harness routing to prevent chafing. If the airbag module has an internal short circuit, replace the left rear side airbag assembly. If the ACM is faulty, replace the airbag control module and perform coding configuration.
  • 6
    System verification and testing: Restore all connections, reconnect the battery, and power on the vehicle. Confirm the SRS warning lamp turns off after 6 seconds. Use VDS or a dedicated diagnostic tool to perform 'SRS system self-check' and 'clear current fault codes'. Confirm DTC B1741 does not return. Perform 'collision output test' (Output Check/Diagnostic Check) to verify circuit resistance is within the normal range (1.5-3.0Ω).
Real-World Cases
BYD DTC AI Analysis

BYD S7 Left Front Window Switch Signal Fault (B1741 Related Case)

✓
Symptoms: The left front window switch could not control the other three door windows, and the switch backlight was flashing. The other windows operated normally from their individual switches. Diagnosis: A VDS scan found DTC B1741 stored in the Left Body Domain Controller (LBDC), indicating an abnormal signal from the left front window switch. LIN bus communication was faulty; power and ground to the switch were normal, but signal transmission was intermittent. Resolution: Replaced the left front door window switch assembly and refreshed the LBDC software, resolving the fault.
Original source ↗
BYD DTC AI Analysis

BYD Tang DM Left Front Seat Control Fault (B1741 Related Case)

✓
Symptoms: The driver's electric seat would not adjust fully rearward, leaving the seat positioned too far forward. The seat memory function also failed. Diagnosis: Checked the seat adjustment motor operation. The motor ran but the position signal was abnormal. Connected VDS and read the left body domain controller, which stored DTC B1741 and related codes. Inspected the wiring harness connectors beneath the seat and found a LIN bus communication fault. Measured the seat position sensor signal voltage; it was abnormal. Resolution: Replaced the driver's seat adjustment switch, repaired the wiring harness connectors under the seat, and relearned the left body domain controller. This cleared the fault.
Original source ↗
BYD DTC AI Analysis

BYD Song Pro Left Domain Controller Communication Fault (B1741-Related Case)

✓
Symptoms: The light switch could not turn on the lights. The wiper switch was inoperative. All steering wheel buttons were unresponsive. The instrument cluster displayed Lane Departure Limited and Lane Keep Limited warnings. Diagnosis: A full vehicle scan with VDS found the Left Body Domain Controller (LBDC) had lost communication with multiple subsystems. Checked the LBDC power supply and ground circuits – normal. Measured CAN and LIN line voltages and found the LIN line shorted to ground. Disconnected each sub-module under the LBDC one by one; traced the fault to an internal short in the left front door switch assembly. Resolution: Replaced the left front door switch assembly (window lift, mirror adjustment, door lock controls) and the LBDC fuse. Fault fully resolved.
Original source ↗
BYD DTC AI Analysis

BYD Song MAX left rear side airbag wiring harness worn and shorted

✓
Symptom: The SRS warning light on the instrument panel stayed on constantly. Scanned the vehicle and retrieved DTC B1741 (left rear side airbag short to ground). No collision history. Diagnosis: Removed the left rear door trim panel and inspected the wiring harness routing at the door hinge. Found the yellow SRS-specific harness sheath had cracked, and the internal airbag igniter wire insulation had worn through, contacting the door metal frame. Confirmed continuity to ground with a multimeter. Solution: Repaired the damaged wiring harness using double-layer heat shrink tubing for insulation. Re-secured the harness routing to avoid contact with sharp edges. Cleared the DTC and the SRS warning light went out normally. System returned to normal.
BYD DTC AI Analysis

Water ingress corroded the airbag connector on a BYD Yuan EV.

✓
Symptoms: After heavy rain, the vehicle displayed B1741 DTC indicating left rear side airbag short to ground. No other abnormalities. Diagnostic Process: Inspected the airbag connector inside the left rear door trim panel and found the seal ring deteriorated and missing. The connector contained obvious water traces and green corrosion. Pins formed a low-resistance path between pins and to ground. Measured airbag module resistance as normal, confirming the fault was on the wiring side. Solution: Thoroughly cleaned the connector contacts, replaced the waterproof seal ring, dried the inside of the wiring harness with compressed air, applied anti-corrosion treatment to the connector, and reinstalled it. This cleared the fault. Recommendation: Check the door drain holes for blockage to prevent further water ingress.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B1737DTC B1737 indicates the Supplemental Restraint System (SRS) detected abnormal continuity between the right middle-row side airbag squib circuit (typically the second-row right seat side airbag or right curtain airbag) and the vehicle power supply (B+, battery positive). The SRS ECU monitors the airbag inflator resistance via an internal current source (normal resistance: 2.0–3.0 Ω). If the ECU detects the voltage across the inflator circuit remaining close to battery voltage (>5 V and approaching 12 V) instead of the expected low potential or floating state, it identifies a short to power. This fault prevents the airbag from deploying normally during a collision because the short circuit bypasses the firing current. In extreme cases, abnormal current can cause unintended deployment, posing a severe safety hazard.B173BDTC B173B indicates an abnormal electric A/C compressor speed feedback signal or a communication fault between the compressor controller and the motor. In BYD new energy models (e.g., Tang, Song, Qin, and Yuan series), this DTC belongs to the HVAC subsystem within the Body Control system and specifically involves the electric compressor closed-loop control circuit. The ECU sets this DTC when the compressor controller (IPM) fails to receive a valid pulse signal from the Hall speed sensor for more than 3 continuous seconds, or when the deviation between the detected actual speed and the target commanded speed exceeds the calibrated threshold (typically >500 rpm). This fault forces the A/C system into fail-safe mode and stops compressor operation. Symptoms include a complete lack of cooling, intermittent cooling, or a sharp decrease in cooling performance. The instrument cluster A/C warning lamp may also illuminate. Prolonged operation with this fault can degrade high-voltage system insulation or cause controller overcurrent damage.
Common problems reported for Seal 6 EV →Seal 6 EV overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.