AU
B177A1B

DTC B177A1B indicates the SRS (Supplemental Restraint System/airbag system) control module detects an open circuit or resistance exceeding the normal threshold (typically >6Ω or infinite) in the left middle-row seat belt pretensioner circuit — Seal 6 EV

Safety System

DTC B177A1B indicates the SRS (Supplemental Restraint System/airbag system) control module detects an open circuit or resistance exceeding the normal threshold (typically >6Ω or infinite) in the left middle-row seat belt pretensioner circuit.

The '1B' sub-code in the BYD diagnostic system typically indicates excessive circuit resistance or an open circuit, causing the ECU to determine the pretensioner is 'not present' or has lost communication.

This fault prevents the system from triggering the left middle-row seat belt pretensioner pyrotechnic device during a collision, increasing occupant forward travel and reducing crash protection.

The system illuminates the instrument cluster airbag fault warning light (SRS light) and may disable the deployment logic for the corresponding side airbag or curtain airbag.

The B177A1B fault code on the Seal 6 EV indicates an open circuit or excessive resistance in the left middle-row seat belt pretensioner circuit. This is a medium-severity SRS fault because the pretensioner may not activate in a crash, reducing occupant protection. Common causes include a loose or poorly connected pretensioner plug, damaged terminals, or an internal pretensioner fault. Visit an authorised dealer for diagnosis and repair. Typical repair cost data is available from recorded cases.
3
Cases Logged
5
Causes
Likely Causes — Seal 6 EV
  • 1Left middle row seat belt pretensioner connector loose, terminal backed out, or poor contact (common after seat removal for repair, failing to reconnect after carpet cleaning, or passenger kicking)
  • 2Pretensioner gas generator internal open circuit (internal igniter open circuit due to component aging, moisture ingress, or impact)
  • 3Wiring harness under the seat slide rail or B-pillar worn or broken (long-term fore/aft seat adjustment causes harness fatigue, or metal edges cut the insulation).
  • 4Driving through water or high-humidity environments causes connector terminal corrosion and oxidation, resulting in high resistance or an open circuit.
  • 5SRS control module internal detection circuit fault (false alarm due to outdated software version, lost calibration data, or damaged hardware sampling circuit)
What To Do
  • 1
    Use the genuine BYD diagnostic tool (VDS2000/3000) to read all fault codes and freeze frame data. Confirm the environmental conditions at the time of the fault (temperature, vehicle speed, etc.) and distinguish between current and historical faults.
  • 2
    Perform safety procedure: Disconnect the battery negative terminal and wait at least 3 minutes (5 minutes for some models) to fully discharge the SRS system energy storage capacitor and prevent accidental airbag deployment.
  • 3
    Locate the left middle-row seat belt pretensioner (usually integrated into the seat belt retractor or below the B-pillar) and visually inspect the connector (usually marked in yellow) for looseness, backed-out pins, water ingress, or corrosion.
  • 4
    Measure the resistance between the pretensioner terminals using a multimeter. The standard value is 1.8Ω - 3.5Ω. If the reading shows infinity (OL) or >6Ω, this confirms an open circuit in the pretensioner body or wiring.
  • 5
    Disconnect the pretensioner connector and measure continuity between the wiring harness side and the SRS ECU. Focus inspection on the seat slide rail mounting points, wear points on the corrugated wiring harness conduit, and the vehicle floor wiring harness clips.
  • 6
    If the pretensioner body resistance is abnormal, replace the left middle-row seat belt assembly (pretensioners are typically non-serviceable; replace the entire seat belt assembly). Note: The new part must match the original vehicle's resistance specification.
  • 7
    If the wiring harness has an open circuit, repair it by soldering (never simply twist wires together), use dual-wall heat-shrink tubing for waterproof insulation, and re-secure the wiring harness to prevent interference with moving parts.
  • 8
    Reconnect all connections and turn on the power. Use the diagnostic tool to clear the fault code, perform the 'SRS system self-check' or 'component test', and confirm B177A1B does not return.
  • 9
    Perform a road test to verify: move the seat forward and backward, and observe if the fault light illuminates intermittently to confirm the fault is completely resolved.
Real-World Cases
BYD DTC AI Analysis

BYD E2 left second-row pretensioner connector oxidised, causing open circuit

✓
The airbag warning light on the instrument panel remained illuminated. VDS showed DTC B177A1B (left middle row seatbelt pretensioner not present). Removed the left middle row seat and found the yellow pretensioner connector terminals severely oxidised due to previous water ingress; green copper corrosion caused infinite contact resistance. Cleaned the terminals with electronic contact cleaner, applied specialist conductive paste and waterproof silicone grease, then reconnected the connector. Fault resolved.
Original source ↗
BYD DTC AI Analysis

BYD Qin EV seat rail wear caused pretensioner harness open circuit

✓
Owner reported the airbag warning light illuminates intermittently on rough roads and clears on smooth surfaces. Retrieved DTC B177A1B as an intermittent fault. Inspection found the wiring harness protective sleeve damaged at the rear mounting point of the left second-row seat rail. When adjusting the seat fore-aft, the metal rail edge cut the harness, causing the internal copper wires to partially sever (intermittent continuity). Repaired the harness and rerouted the wiring, added rubber protective sleeves and securing clips to prevent contact with the rail. Fault fully resolved.
Original source ↗
BYD DTC AI Analysis

BYD E3 Airbag Control Module Spurious Fault

✓
No collision repair history. SRS warning light suddenly illuminated on the dash. Retrieved DTCs B177A1B (left middle row), B177B1B (right middle row), and other pretensioner faults. All pretensioner resistance measured 2.0Ω (normal); wiring harness continuity normal. Diagnosed as SRS ECU internal software bug causing false alarm. Performed SRS module software upgrade using VDS (V1.2 to V1.5), cleared DTCs. Fault has not recurred.
Original source ↗
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B1737DTC B1737 indicates the Supplemental Restraint System (SRS) detected abnormal continuity between the right middle-row side airbag squib circuit (typically the second-row right seat side airbag or right curtain airbag) and the vehicle power supply (B+, battery positive). The SRS ECU monitors the airbag inflator resistance via an internal current source (normal resistance: 2.0–3.0 Ω). If the ECU detects the voltage across the inflator circuit remaining close to battery voltage (>5 V and approaching 12 V) instead of the expected low potential or floating state, it identifies a short to power. This fault prevents the airbag from deploying normally during a collision because the short circuit bypasses the firing current. In extreme cases, abnormal current can cause unintended deployment, posing a severe safety hazard.B173BDTC B173B indicates an abnormal electric A/C compressor speed feedback signal or a communication fault between the compressor controller and the motor. In BYD new energy models (e.g., Tang, Song, Qin, and Yuan series), this DTC belongs to the HVAC subsystem within the Body Control system and specifically involves the electric compressor closed-loop control circuit. The ECU sets this DTC when the compressor controller (IPM) fails to receive a valid pulse signal from the Hall speed sensor for more than 3 continuous seconds, or when the deviation between the detected actual speed and the target commanded speed exceeds the calibrated threshold (typically >500 rpm). This fault forces the A/C system into fail-safe mode and stops compressor operation. Symptoms include a complete lack of cooling, intermittent cooling, or a sharp decrease in cooling performance. The instrument cluster A/C warning lamp may also illuminate. Prolonged operation with this fault can degrade high-voltage system insulation or cause controller overcurrent damage.
Common problems reported for Seal 6 EV →Seal 6 EV overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.