AU
B1785

This fault code indicates the driver-side dual-stage airbag Stage 2 squib circuit resistance falls below the standard threshold (typically <1 — Seal 6 EV

Safety System

This fault code indicates the driver-side dual-stage airbag Stage 2 squib circuit resistance falls below the standard threshold (typically <1.0Ω; standard value 2.0-3.0Ω).

Electrically, this indicates a short circuit in the airbag ignition circuit (short to ground or wire-to-wire short).

The second stage deploys based on collision severity.

Low resistance causes the SRS ECU to detect a circuit fault and disable airbag deployment, or in extreme cases, abnormal current triggers unintended deployment.

This hard fault in the active safety system triggers an airbag self-test failure, disables the entire front-row frontal airbag protection function, and poses a severe safety hazard.

The B1785 fault code on the Seal 6 EV indicates low resistance in the driver-side dual-stage airbag Stage 2 squib circuit, usually caused by a short circuit. Severity is medium because it can disable front airbag protection and may create a serious safety risk. Common causes include an internal short in the driver airbag module or a faulty clock spring. Visit an authorised dealer for diagnosis and repair. Typical repair cost data is available.
3
Cases Logged
5
Causes
Likely Causes — Seal 6 EV
  • 1Airbag module internal squib short circuit: The Stage 2 gas generator squib inside the driver airbag assembly shorts internally due to moisture ingress, aging, or manufacturing defects.
  • 2Internal short circuit in the clock spring (spiral cable): The clock spring coil under the steering wheel wears and breaks from long-term rotation, causing the wire end to short to ground, or the internal slip ring short-circuits.
  • 3Harness chafed and shorted to ground: The harness from the SRS ECU to the steering wheel rubs against the steering column, instrument panel frame, or similar areas, damaging the insulation and contacting the vehicle body metal.
  • 4Connector water ingress or corrosion: Poor sealing allows water to enter the airbag wiring harness connector (usually located below the steering wheel or behind the airbag), causing a short circuit between terminals or a short to ground.
  • 5SRS ECU internal detection circuit fault: Airbag control unit internal sampling resistor or A/D conversion circuit failure causes inaccurate resistance detection (relatively uncommon).
What To Do
  • 1
    Safe power-down and wait: Disconnect the low-voltage battery negative terminal, wait at least 90 seconds (to allow the SRS capacitor to fully discharge), and record the original fault code.
  • 2
    Visual inspection: Check the airbag wiring harness connector below the steering wheel and the clock spring connector for looseness, water ingress, corrosion, or burn marks. Check the wiring harness around the steering column for wear.
  • 3
    Airbag module isolation test: Remove the driver airbag and disconnect the connector. Use a digital multimeter to measure the resistance between the second-stage ignition pins on the airbag plug side (normal: 2.0-3.0 Ω). If the resistance is <1.0 Ω, replace the airbag assembly.
  • 4
    Harness continuity check: Disconnect the connector between the SRS ECU and the clock spring. Measure the harness resistance from the ECU side to the clock spring input side (should be <1 Ω). Measure the resistance of each wire to body ground (should be >1 MΩ). If the resistance to ground is too low, inspect the harness for damage.
  • 5
    Clock spring verification: Remove the clock spring, measure continuity between the corresponding input and output pins, and measure insulation between each pin and the housing. If the second-stage circuit has a short circuit or poor insulation, replace the clock spring.
  • 6
    ECU confirmation: If all above checks are normal, install a known-good airbag module and clock spring for testing. If the fault code persists, the SRS ECU is faulty. Replace the control unit.
  • 7
    Repair and verification: After replacing the faulty component, reconnect all connectors and restore power. Use VDS or an OEM diagnostic tool to clear the fault code. Perform an SRS system self-check (Active Test). Verify B1785 does not return and the airbag warning light turns off.
Real-World Cases
BYD DTC AI Analysis

Internal short in clock spring caused B1785

✓
2020 BYD Qin Pro, 80,000 km. Owner reported the airbag warning light illuminating intermittently when turning the steering wheel to specific angles. VDS scan showed DTC B1785 (current fault). Disassembly revealed the clock spring's second-stage airbag flat cable worn through at rotational limit positions; exposed copper contacted the metal housing, causing a short to ground. Replaced the clock spring; new component measured 2.3Ω. Cleared fault codes after installation and performed multiple full-lock steering tests. Fault did not reoccur.
BYD DTC AI Analysis

Moisture ingress caused internal short circuit in airbag module

✓
A 2019 BYD Yuan EV had water leaking through the front windshield into the driver's side A-pillar and the airbag warning light constantly on. B1785 showed as a current fault and would not clear. Disconnected the airbag connector; the harness side measured infinite resistance to ground (normal), but the second-stage ignition pins on the module measured only 0.3Ω—indicating an internal short in the igniter. Removed the airbag and found the gas generator seal had deteriorated, allowing water in. Replaced the driver airbag assembly and repaired the windshield seal. Fault resolved.
BYD DTC AI Analysis

Steering wheel modification damaged the wiring harness

✓
2021 BYD Tang DM. The owner installed a racing steering wheel and later restored the factory unit, triggering the SRS warning light. DTC B1785 indicated resistance below specification (0.8Ω). Inspection revealed the modification had overstretched the airbag wiring harness, deforming terminals inside the connector below the steering column. The second-stage airbag circuit terminal shorted to an adjacent terminal. Repaired the connector terminals, rerouted the wiring with adequate slack, and restored normal resistance (2.1Ω). Fault resolved.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B1737DTC B1737 indicates the Supplemental Restraint System (SRS) detected abnormal continuity between the right middle-row side airbag squib circuit (typically the second-row right seat side airbag or right curtain airbag) and the vehicle power supply (B+, battery positive). The SRS ECU monitors the airbag inflator resistance via an internal current source (normal resistance: 2.0–3.0 Ω). If the ECU detects the voltage across the inflator circuit remaining close to battery voltage (>5 V and approaching 12 V) instead of the expected low potential or floating state, it identifies a short to power. This fault prevents the airbag from deploying normally during a collision because the short circuit bypasses the firing current. In extreme cases, abnormal current can cause unintended deployment, posing a severe safety hazard.B173BDTC B173B indicates an abnormal electric A/C compressor speed feedback signal or a communication fault between the compressor controller and the motor. In BYD new energy models (e.g., Tang, Song, Qin, and Yuan series), this DTC belongs to the HVAC subsystem within the Body Control system and specifically involves the electric compressor closed-loop control circuit. The ECU sets this DTC when the compressor controller (IPM) fails to receive a valid pulse signal from the Hall speed sensor for more than 3 continuous seconds, or when the deviation between the detected actual speed and the target commanded speed exceeds the calibrated threshold (typically >500 rpm). This fault forces the A/C system into fail-safe mode and stops compressor operation. Symptoms include a complete lack of cooling, intermittent cooling, or a sharp decrease in cooling performance. The instrument cluster A/C warning lamp may also illuminate. Prolonged operation with this fault can degrade high-voltage system insulation or cause controller overcurrent damage.
Common problems reported for Seal 6 EV →Seal 6 EV overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.