AU
C050E00

DTC C050E00 indicates the IPB (Intelligent Integrated Braking System) or ABS module detects an abnormal short circuit to vehicle ground (GND) in the left rear wheel speed sensor (WSS) power supply circuit (typically the 12V supply line) — Seal 6 EV

Braking System

DTC C050E00 indicates the IPB (Intelligent Integrated Braking System) or ABS module detects an abnormal short circuit to vehicle ground (GND) in the left rear wheel speed sensor (WSS) power supply circuit (typically the 12V supply line).

This supply circuit provides the operating voltage for the Hall-effect or magnetic wheel speed sensor.

When a short to ground occurs, the power driver circuit inside the ABS module detects overcurrent or a voltage drop to nearly 0V, triggering the protection mechanism and storing the fault code.

This fault causes a missing or abnormal left rear wheel speed signal, forcing active safety functions such as ABS, ESC, TCS, and Automatic Emergency Braking (AEB) into fail-safe mode (conventional braking).

The instrument cluster illuminates multiple warning lamps, including ABS, ESC, and EBD.

This severely compromises driving safety and creates a risk of wheel lock-up, especially on slippery roads or during emergency braking.

The C050E00 fault code on the Seal 6 EV indicates a high-severity short to ground in the left rear wheel speed sensor power supply circuit, detected by the IPB/ABS module. This can disable or limit ABS, ESC, TCS, EBD, and AEB, increasing braking risk. Common causes include damaged sensor wiring insulation rubbing on body or suspension parts, or an internally shorted sensor. Visit an authorised dealer for diagnosis and repair. Typical repair cost data is available.
4
Cases Logged
5
Causes
Likely Causes — Seal 6 EV
  • 1Damaged or aged insulation on the left rear wheel speed sensor wiring harness rubs against metal components such as the body longitudinal beam, suspension bracket, or fender liner during driving, grounding to the chassis and causing a power wire short to ground.
  • 2Short circuit between the wheel speed sensor internal power supply pin and the sensor housing or ground pin (typically resulting from water ingress due to sensor seal failure, internal coil burnout, or circuit board breakdown).
  • 3Water enters the sensor connector (located at the left rear fender or chassis wiring harness joint) due to driving through water, high-pressure washing, or an aging sealing ring, causing an electrolytic short circuit or corrosion-induced continuity between the internal power and ground terminals.
  • 4A breakdown short circuit in the ABS/IPB control module internal power drive circuit (such as a MOSFET or intelligent power chip) causes the output port to remain continuously grounded.
  • 5Vehicle accident repairs, chassis modifications, or improper wiring harness securing pinch or crush the wiring harness, or loosen retaining clips, allowing the harness to rub against rotating components (such as the half shaft or brake disc dust shield) and cause wear.
What To Do
  • 1
    Connect the VDS or dedicated diagnostic tool and read the freeze frame data for DTC C050E00. Record key parameters at the time of the fault, such as vehicle speed, voltage, and temperature. Clear the fault code and perform a road test to confirm if the fault is persistent.
  • 2
    Raise the vehicle and remove the left rear wheel. Visually inspect the wheel speed sensor for physical damage. Inspect the sensor connector (usually located near the shock absorber or body wiring harness connection) for water ingress, terminal corrosion, loose connections, or damaged wiring insulation.
  • 3
    Disconnect the left rear wheel speed sensor connector. Use a multimeter to measure the resistance between the sensor-side power supply pin and body ground. The normal value is greater than 10MΩ (open circuit). A resistance below 1Ω indicates a short circuit. Measure the resistance to ground of the corresponding pin on the ABS module side to determine if the short circuit is in the wiring harness or internal to the module.
  • 4
    If the wiring harness shorts to ground, strip the harness sheath in sections from the left rear wheel hub to the ABS module (usually located in the engine compartment or cabin firewall). Inspect the sections passing through body panel holes, retaining clips, and areas adjacent to suspension components to locate damaged insulation. After repair, wrap the area with a double layer of waterproof insulating tape or heat-shrink tubing.
  • 5
    If the wiring harness is normal, measure the resistance between the power supply and ground pins on the wheel speed sensor body (normally open circuit or high resistance). If the resistance is abnormally low (<100Ω), this indicates an internal sensor short circuit. Replace the left rear wheel speed sensor (BYD part numbers usually start with SC- or HA-).
  • 6
    If the sensor and wiring harness are normal, measure the resistance between the corresponding power supply pin of the ABS/IPB module connector and ground. A short circuit indicates an internal module fault. Replace the IPB assembly or ABS control unit (perform coding, matching, and bleeding procedures).
  • 7
    After completing the repair, reconnect all connectors, use the diagnostic tool to clear the fault code, and perform a dynamic test: drive in a straight line at 20-40 km/h and verify the left rear wheel speed signal in the data stream synchronizes with the right rear and front wheel speeds; perform an emergency braking test to confirm the ABS functions normally and the fault code does not return.
Real-World Cases
BYD DTC AI Analysis

Seal 6 DM-i left rear wheel speed sensor harness chafed and shorted to ground

✓
While driving, the ABS and ESC warning lights suddenly lit up on the dash with a 'check brake system' alert. The scan tool pulled DTC C050E00 (left rear wheel speed sensor signal circuit short to ground). Inspection found the left rear wheel speed sensor wiring harness retaining clip had come loose where it passes through the body rail, allowing the harness to chafe against the rear suspension lower control arm. Prolonged friction damaged the insulation, exposing the copper core and shorting it to the metal bracket. Repair: Cut out the damaged section and soldered in a repair wire. Rerouted the harness and protected it with corrugated tubing and waterproof tape. Repositioned the retaining clip to prevent interference with moving parts. Replaced the wheel speed sensor, cleared the fault codes and road tested. Wheel speed signal returned to normal.
Original source ↗
BYD DTC AI Analysis

Song PLUS DM-i sensor connector corroded and shorted after water ingress

✓
After driving through flood water, the dashboard displayed a brake system fault and the ABS failed. Scanned DTCs C050E00 and C050C00 (wiring harness fault). Removed the left rear wheel speed sensor connector (located behind the left rear wheel arch liner) and found substantial muddy water deposits inside. Electrolytic corrosion between the power pin (normally red wire) and ground pin (black wire) had created green copper oxide, shorting the pins. Repair: Thoroughly cleaned the connector pins with electrical contact cleaner and sandpaper, replaced the waterproof seal, and applied silicone sealant at the connector mating surface to improve waterproofing. Measured sensor supply voltage at 12V (normal). Cleared the fault codes—fault resolved. Inspect the seals on other chassis wiring harness connectors.
Original source ↗
BYD DTC AI Analysis

Internal short circuit in wheel speed sensor body caused intermittent fault

✓
Cold starts are normal, but the ABS light comes on after roughly 10 minutes of driving. Shutting off and restarting the engine clears the fault, but it returns. Scanner shows DTC C050E00. Freeze frame data indicates the left rear wheel speed was 0 km/h when the fault triggered, while the other wheels read normally. Static resistance tests on the sensor were normal, but hot-state testing (using a heat gun to simulate operating temperature) showed a sharp resistance drop between power and ground. Diagnosis: thermal fatigue failure of the internal coil insulation. Repair: Replace the left rear wheel speed sensor (use the correct type—variable reluctance or Hall effect; Song PLUS DM-i usually has two-wire Hall or variable reluctance sensors). Adjust the sensor-to-tone ring gap to 0.3–1.2 mm during installation and apply grease to prevent seizing.
Original source ↗
BYD DTC AI Analysis

Internal drive circuit fault in IPB integrated brake module

✓
Repair case reference: After confirming the left rear wheel speed sensor, wiring harness, and connectors were normal, measured a continuous short to ground (resistance <1Ω) between the IPB (Integrated Power Brake) module’s left rear wheel speed sensor power supply terminal (typically marked RR+ or Vbat_RL) and ground. The short persisted at the module terminal even with the harness disconnected. Diagnosed as internal power management chip (LDO or MOSFET) breakdown in the IPB module. Fix: Replace the entire integrated brake unit (IPB is a complete assembly; part number varies by model—for example, the Song PLUS DM-i requires the IPB assembly). Post-replacement, perform IPB coding and configuration, longitudinal acceleration sensor calibration, brake line bleeding, and ESC function testing using a diagnostic tool. Fault resolved.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B1737DTC B1737 indicates the Supplemental Restraint System (SRS) detected abnormal continuity between the right middle-row side airbag squib circuit (typically the second-row right seat side airbag or right curtain airbag) and the vehicle power supply (B+, battery positive). The SRS ECU monitors the airbag inflator resistance via an internal current source (normal resistance: 2.0–3.0 Ω). If the ECU detects the voltage across the inflator circuit remaining close to battery voltage (>5 V and approaching 12 V) instead of the expected low potential or floating state, it identifies a short to power. This fault prevents the airbag from deploying normally during a collision because the short circuit bypasses the firing current. In extreme cases, abnormal current can cause unintended deployment, posing a severe safety hazard.B173BDTC B173B indicates an abnormal electric A/C compressor speed feedback signal or a communication fault between the compressor controller and the motor. In BYD new energy models (e.g., Tang, Song, Qin, and Yuan series), this DTC belongs to the HVAC subsystem within the Body Control system and specifically involves the electric compressor closed-loop control circuit. The ECU sets this DTC when the compressor controller (IPM) fails to receive a valid pulse signal from the Hall speed sensor for more than 3 continuous seconds, or when the deviation between the detected actual speed and the target commanded speed exceeds the calibrated threshold (typically >500 rpm). This fault forces the A/C system into fail-safe mode and stops compressor operation. Symptoms include a complete lack of cooling, intermittent cooling, or a sharp decrease in cooling performance. The instrument cluster A/C warning lamp may also illuminate. Prolonged operation with this fault can degrade high-voltage system insulation or cause controller overcurrent damage.
Common problems reported for Seal 6 EV →Seal 6 EV overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.