AU
C051500

DTC C051500 indicates the IPB (Intelligent Integrated Braking System) detected a short circuit to battery positive (B+) in the right rear wheel speed sensor power supply circuit — Seal 6 EV

Braking System

DTC C051500 indicates the IPB (Intelligent Integrated Braking System) detected a short circuit to battery positive (B+) in the right rear wheel speed sensor power supply circuit.

This fault occurs when abnormal electrical continuity develops between the sensor power line (typically a 12V supply) and the vehicle constant power supply or the IPB internal power output stage, causing an abnormal voltage increase or current overload.

The IPB control unit monitors the supply circuit voltage and current characteristics.

Upon detecting a short circuit, it triggers a protection mechanism and cuts power to the circuit to prevent hardware damage.

This fault causes the loss of the right rear wheel speed signal, disabling or degrading ABS, ESP, TCS, EPB, and Automatic Emergency Braking (AEB) functions, which severely compromises driving safety.

The '00' suffix in the DTC typically indicates an active, hard fault (non-intermittent).

The C051500 fault code on the Seal 6 EV indicates a high-severity short to battery positive in the right rear wheel speed sensor power supply circuit. This can cut the sensor signal and affect ABS, ESP, TCS, EPB, and AEB operation. Common causes include damaged harness insulation or water ingress and corrosion at the sensor connector. The recommended fix is to visit an authorised dealer for diagnosis and repair. Typical repair cost data is available.
5
Cases Logged
5
Causes
Likely Causes — Seal 6 EV
  • 1Right rear wheel speed sensor harness insulation damaged: Long-term vibration and friction at the rubber grommet where the harness passes through the body floor or suspension control arm damages the insulation. The power supply wire contacts and shorts to an adjacent constant power circuit (such as the tail light or fuel pump power supply).
  • 2Sensor connector water ingress and corrosion: Vehicle wading, direct high-pressure water jets, or poor sealing causes an internal short circuit in the connector, shorting the power supply terminal to an adjacent high-potential terminal or the metal housing.
  • 3Wheel speed sensor internal circuit breakdown: Damage to the internal voltage regulator circuit or Hall element shorts the power input terminal to the signal output terminal or housing, creating a reverse short circuit to the power supply circuit.
  • 4IPB control unit internal power module fault: Output stage breakdown of the wheel speed sensor power supply chip (LDO or DC-DC) inside the IPB causes continuous high voltage output or an internal short circuit. Similar faults in other wheel speed sensors controlled by the same IPB usually accompany this condition.
  • 5Harness damage from improper modification or accident repair: improperly splicing wires to draw power for aftermarket equipment (such as dash cams or reversing sensors), or incorrectly wrapping the harness during rear-end accident repairs, resulting in crushed or misconnected power supply wires.
What To Do
  • 1
    Safety Preparation and Fault Confirmation: Use VDS2000 or Launch X431 to read all fault codes. Confirm if C051500 appears alone or alongside other wheel speed sensor faults, such as C051400 (short to ground). Record freeze frame data (vehicle speed, temperature, and voltage at the time of occurrence). Check the IPB software version and verify no related Technical Service Bulletins (TSBs) apply.
  • 2
    Visual and connector inspection: Raise the vehicle, remove the right rear tire, and inspect the wheel speed sensor connector (usually located near the steering knuckle or brake caliper) for signs of water ingress, corrosion, looseness, or deformed pins. Follow the wiring routing and inspect the harness sleeve for damage. Focus on the bent sections passing through the body floor panel and suspension control arm.
  • 3
    Power supply voltage and resistance measurement: Turn off the ignition. Disconnect the right rear wheel speed sensor connector. Measure the resistance to ground at the power supply pin on the connector side (usually pin 1 or 2; refer to the wiring diagram). Normal resistance is greater than 10 MΩ. If the resistance is too low, the circuit is shorted to power. Turn on the ignition. Measure the voltage at this pin. Normal voltage is 12 V ± 0.5 V. If the measured voltage equals battery voltage (above 12.6 V) and shows direct continuity to the battery positive terminal, this confirms a short circuit.
  • 4
    Wiring insulation and continuity test: Disconnect the right trunk wiring harness connector (usually located near the right rear fender liner) to divide the circuit into the 'sensor-to-body transition section' and the 'body-to-IPB section'. Use a megohmmeter to measure the insulation resistance from the power supply wire to the body and to other power wires to isolate the faulty section. Inspect the IPB control unit connector (located near the engine compartment firewall) for water ingress or corrosion.
  • 5
    Component replacement verification: If wiring insulation is normal, replace the right rear wheel speed sensor (typical part number 3630200-00; verify vehicle model compatibility) and test. If the fault persists after replacing the sensor and the wiring harness tests normal, this indicates a damaged internal power supply module in the IPB control unit. Replace the IPB assembly (requires bleeding, calibration, and coding).
  • 6
    Repair Verification and Function Test: After repairing or replacing the faulty component, clear the fault code and perform a road test (speed must exceed 40 km/h to activate the wheel speed signal self-check). Use a diagnostic tool to read the wheel speed sensor live data stream. Confirm the right rear wheel speed matches the other wheel speeds with no dropouts or spikes. Test the ABS, ESP, and EPB functions for normal operation and confirm the warning light is off.
Real-World Cases
BYD DTC AI Analysis

Song PLUS DM-i: Right rear wheel speed sensor power supply short circuit after water ingress

✓
2022 Song PLUS DM-i. ABS and ESP lights stayed on after driving through water. Read DTC C051500. Inspection found obvious water stains and verdigris inside the right rear wheel speed sensor connector; the power supply pin was conducting to the connector housing. Water had seeped through the connector seal during wading, causing the power terminal to short to ground (body)—misdiagnosed as a short to power (or actually shorted to the internal power wire). Cleaned the connector pins, applied conductive grease, replaced the sensor (possible internal damage), and resealed the waterproofing. Fault resolved.
BYD DTC AI Analysis

Worn wiring harness sheath caused intermittent short circuit

✓
2021 Song Pro DM. ESP warning light occasionally illuminates on rough roads; intermittent DTC C051500. On the lift, found the right rear wheel speed sensor harness worn at the rubber grommet where it passes through the suspension arm. Internal insulation had worn through, allowing the power wire to contact an adjacent constant-power reverse light wire. Static measurements normal, but resistance varied when shaking the harness. Repair: Repaired the damaged harness, separated the routing to avoid interference, and added an abrasion-resistant sleeve. Fault has not reoccurred.
BYD DTC AI Analysis

Internal fault in the IPB control unit caused abnormal power supply to multiple sensors.

✓
2023 Seal. DTCs C051500 and C051100 appeared after rear-end collision repairs (left rear wheel speed sensor supply short circuit). Wiring measured normal on both sides, but supply voltage read 14.5V (battery voltage), suggesting IPB internal voltage regulator damage. Traced to a flat 12V battery during the accident; jump starter connected with reversed polarity, causing surge damage to the IPB power module. Replaced the IPB integrated brake assembly, performed hydraulic bleeding, longitudinal sensor calibration, and wheel speed sensor signal learning. Fault resolved.
BYD DTC AI Analysis

Aftermarket reversing sensors incorrectly connected, causing short circuit

✓
2022 Song MAX. Owner installed a reversing camera at a non-authorized shop; DTC C051500 appeared the next day. Inspection found the installer cut into the right rear sill harness to draw power and mistakenly bridged the reverse light supply to the wheel speed sensor power feed, causing high current to enter the sensor circuit. Removed the non-compliant wiring, repaired the damaged factory harness (replaced the entire section to eliminate risks), and restored the original circuits. Explained the risks of unauthorized modifications to the owner.
BYD DTC AI Analysis

Sensor internal short triggered IPB protection

✓
2020 Han EV. C051500 triggered suddenly at 60,000 km. Found 0.5Ω short between the sensor connector supply pin and ground. Disconnected the sensor; harness side tested normal with 12V supply and infinite resistance to ground. Disassembled the sensor and found the internal Hall element burnt with supply and ground terminals shorted. Suspected cause: sensor ageing or internal Zener diode breakdown. Replaced the right rear wheel speed sensor (genuine part), cleared the fault codes, and road test returned to normal. Also check tire balance to rule out long-term overheating from abnormal tire vibration causing premature sensor ageing.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B1737DTC B1737 indicates the Supplemental Restraint System (SRS) detected abnormal continuity between the right middle-row side airbag squib circuit (typically the second-row right seat side airbag or right curtain airbag) and the vehicle power supply (B+, battery positive). The SRS ECU monitors the airbag inflator resistance via an internal current source (normal resistance: 2.0–3.0 Ω). If the ECU detects the voltage across the inflator circuit remaining close to battery voltage (>5 V and approaching 12 V) instead of the expected low potential or floating state, it identifies a short to power. This fault prevents the airbag from deploying normally during a collision because the short circuit bypasses the firing current. In extreme cases, abnormal current can cause unintended deployment, posing a severe safety hazard.B173BDTC B173B indicates an abnormal electric A/C compressor speed feedback signal or a communication fault between the compressor controller and the motor. In BYD new energy models (e.g., Tang, Song, Qin, and Yuan series), this DTC belongs to the HVAC subsystem within the Body Control system and specifically involves the electric compressor closed-loop control circuit. The ECU sets this DTC when the compressor controller (IPM) fails to receive a valid pulse signal from the Hall speed sensor for more than 3 continuous seconds, or when the deviation between the detected actual speed and the target commanded speed exceeds the calibrated threshold (typically >500 rpm). This fault forces the A/C system into fail-safe mode and stops compressor operation. Symptoms include a complete lack of cooling, intermittent cooling, or a sharp decrease in cooling performance. The instrument cluster A/C warning lamp may also illuminate. Prolonged operation with this fault can degrade high-voltage system insulation or cause controller overcurrent damage.
Common problems reported for Seal 6 EV →Seal 6 EV overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.