AU
U0155-00

U0155-00 is a CAN bus communication fault code indicating interrupted data communication between the airbag control unit (SRS ECU) and the instrument cluster — Seal 6 EV

Safety System

U0155-00 is a CAN bus communication fault code indicating interrupted data communication between the airbag control unit (SRS ECU) and the instrument cluster.

In the BYD CAN network architecture, the SRS module transmits airbag status, system fault information, and collision trigger signals in real time to the instrument cluster via the powertrain CAN or body CAN bus.

The SRS sets this fault code if it fails to receive a response message from the instrument cluster within the predetermined cycle (usually 250ms-500ms) or detects a bus physical layer fault.

This fault may prevent the instrument panel from normally illuminating the SRS fault warning lamp and, in extreme cases, affects the safety warning function during a collision.

It classifies as a Level 2 safety-related fault.

The U0155-00 fault code on the Seal 6 EV indicates a medium-severity CAN bus communication fault between the airbag control unit and the instrument cluster. It may stop the cluster from showing the SRS warning correctly. Common causes include a blown cluster fuse, poor power connection, or CAN wiring faults such as shorts or open circuits. Visit an authorised dealer for diagnosis and repair. Typical repair cost data is available from recorded cases.
5
Cases Logged
5
Causes
Likely Causes — Seal 6 EV
  • 1Instrument cluster power supply system fault (blown instrument cluster fuse, poor connection in IGN power circuit, open circuit in constant +B power circuit)
  • 2CAN bus physical layer fault (CAN-H to CAN-L short circuit, short to ground or power, open circuit, or excessive contact resistance)
  • 3Poor module ground (loose, oxidized, or corroded instrument cluster or SRS ground point causing increased signal circuit impedance)
  • 4Damaged internal CAN transceiver in the instrument cluster (electrostatic breakdown or chip aging prevents decoding of bus messages)
  • 5Gateway module routing fault (on some models, the SRS and instrument cluster forward data through the gateway; a gateway fault interrupts communication)
What To Do
  • 1
    Use VDS2000 or the BYD dedicated diagnostic tool to perform a full-vehicle DTC scan. Confirm if U0155-00 appears alone or alongside other U01XX series communication faults to determine if it is a single-point fault.
  • 2
    Check the instrument cluster power supply: Measure the voltage at instrument cluster connector terminal 30 (constant power +B) and terminal 15 (IGN). The standard value is 12V ± 0.5V. Check the continuity of instrument cluster-related fuses such as FB-02 and FB-22.
  • 3
    Check module ground: Measure the resistance between the instrument cluster GND and body ground, and between the SRS module GND and body ground. Resistance must be less than 1Ω. Check the tightness of the G202 ground point under the left A-pillar of the dashboard.
  • 4
    CAN bus physical layer check: With power off, measure the terminal resistance between OBD diagnostic connector pin 6 (CAN-H) and pin 14 (CAN-L). Standard value: 60 Ω ± 5 Ω. With power on, measure the CAN-H to ground voltage (2.5-3.5 V) and CAN-L to ground voltage (1.5-2.5 V).
  • 5
    Harness continuity test: Disconnect the battery negative terminal, measure the continuity of the CAN harness between the instrument cluster and the SRS (resistance between pins should be <1Ω), and check the 20-pin connector behind the dashboard for backed-out pins or oxidation.
  • 6
    Perform a network sleep/wake test: Disconnect the 12V battery negative terminal for more than 5 minutes, reconnect power, and observe if the fault temporarily disappears to determine if a module crash caused a soft fault.
  • 7
    Module replacement verification: After confirming the wiring is normal, first swap the instrument cluster with one of the same model (prepare for immobilizer matching) to determine if the internal CAN transceiver is faulty.
  • 8
    SRS module programming check: If the fault persists after replacing the instrument cluster, check the SRS module software version. Update or replace the SRS control unit if necessary.
Real-World Cases
BYD DTC AI Analysis

Loose instrument panel wiring harness connector causes intermittent U0155 on Qin EV450

✓
A 2018 Qin EV450 had intermittent instrument cluster blackouts and a constant SRS warning light while driving; DTC U0155-00 was intermittent. Inspection found the 20-pin connector behind the instrument cluster had not fully locked. Road vibration caused poor contact on the CAN-H pin, with contact resistance at 12Ω (spec <1Ω). Reinstalled the connector and applied electrical contact protector; the fault has not returned.
BYD DTC AI Analysis

Aftermarket full-LCD instrument cluster modification causes communication protocol mismatch on Tang DM

✓
After the owner installed an aftermarket full LCD instrument cluster, the SRS system continuously logged U0155-00 and the code would not clear. The modified cluster used a non-standard CAN baud rate (250kbps vs factory 500kbps), causing a communication handshake failure with the SRS module. Communication returned to normal after restoring the factory instrument cluster and re-matching the immobilizer.
BYD DTC AI Analysis

Song Pro EV A-Pillar Wiring Harness Corrosion Case After Water Ingress

✓
After driving through water, the dashboard displayed "Please check SRS system". The diagnostic tool read DTC U0155-00. Disassembly revealed the weatherproof grommet below the left A-pillar was damaged. Water had entered the wiring harness connector and caused oxidation; green copper corrosion between the CAN-H and CAN-L pins attenuated the signal. Cleaned the connector with precision electrical contact cleaner, repaired the waterproof seal, and sprayed WD-40 for protection. Fault cleared.
BYD DTC AI Analysis

Qin Pro DM instrument cluster fuse blown with internal short circuit

✓
Vehicle failed to power up with no instrument cluster display. Fault codes included U0155-00 and multiple power supply faults. Inspection found instrument cluster fuse FB-22 blown; the replacement blew immediately. Disassembling the cluster revealed an internal DC-DC converter short. Replaced the cluster with an OEM unit and the instrument panel distribution box. System returned to normal.
BYD DTC AI Analysis

Han EV gateway module failure caused loss of communication between multiple systems

✓
2022 Han EV. Instrument cluster and multimedia both reported communication faults. SRS system stored U0155-00 with additional lost-communication codes for BCM and EPS. CAN bus voltage at the diagnostic port: CAN-H 1.2V, CAN-L 0.8V (abnormal). Disconnected the gateway module (located beneath the center console) and bus voltage returned to normal. Diagnosed as internal CAN transceiver chip failure in the gateway. Replaced the gateway module and performed online coding and configuration; fault resolved.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B1737DTC B1737 indicates the Supplemental Restraint System (SRS) detected abnormal continuity between the right middle-row side airbag squib circuit (typically the second-row right seat side airbag or right curtain airbag) and the vehicle power supply (B+, battery positive). The SRS ECU monitors the airbag inflator resistance via an internal current source (normal resistance: 2.0–3.0 Ω). If the ECU detects the voltage across the inflator circuit remaining close to battery voltage (>5 V and approaching 12 V) instead of the expected low potential or floating state, it identifies a short to power. This fault prevents the airbag from deploying normally during a collision because the short circuit bypasses the firing current. In extreme cases, abnormal current can cause unintended deployment, posing a severe safety hazard.B173BDTC B173B indicates an abnormal electric A/C compressor speed feedback signal or a communication fault between the compressor controller and the motor. In BYD new energy models (e.g., Tang, Song, Qin, and Yuan series), this DTC belongs to the HVAC subsystem within the Body Control system and specifically involves the electric compressor closed-loop control circuit. The ECU sets this DTC when the compressor controller (IPM) fails to receive a valid pulse signal from the Hall speed sensor for more than 3 continuous seconds, or when the deviation between the detected actual speed and the target commanded speed exceeds the calibrated threshold (typically >500 rpm). This fault forces the A/C system into fail-safe mode and stops compressor operation. Symptoms include a complete lack of cooling, intermittent cooling, or a sharp decrease in cooling performance. The instrument cluster A/C warning lamp may also illuminate. Prolonged operation with this fault can degrade high-voltage system insulation or cause controller overcurrent damage.
Common problems reported for Seal 6 EV →Seal 6 EV overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.