NO
AU
B110E09

This DTC indicates a functional failure of the temperature and humidity sensing module in the PM2 — Atto 3

Thermal Management System

This DTC indicates a functional failure of the temperature and humidity sensing module in the PM2.5 air quality rapid detection system.

This module integrates into the PM2.5 detector and monitors ambient air temperature and relative humidity in real time.

The system uses these readings to compensate and correct the light-scattering measurement data from the laser particulate sensor, as temperature and humidity changes significantly affect PM2.5 detection accuracy.

An abnormal analog signal or digital communication interruption causes this fault.

This prevents the air conditioning controller from obtaining accurate ambient temperature and humidity parameters, disabling the automatic air purification, negative ion generator linkage, and air quality display functions.

Although the system classifies this as a "severe" fault, it only affects comfort features and does not impact the powertrain or driving safety.

The vehicle can travel a short distance to a repair facility.

3
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin Pro DM instrument cluster intermittently displays 'Air Quality Detection Fault'

✓
After parking overnight, started the vehicle. The dashboard indicated an air quality system fault, and the air conditioning auto mode could not activate the purification function. Retrieved current fault code B110E09 using a diagnostic tool. Inspection found the PM2.5 sensor above the centre console; its wiring harness plug retaining clip had broken, causing the connector to work loose. When the vehicle vibrated during driving, the signal would cut out. Resecured the plug and reinforced it with cable ties. Cleared the fault codes and observed the temperature and humidity data displayed normally. Fault resolved.
BYD DTC AI Analysis

Qin Pro EV PM2.5 function inoperative after air conditioning repair

✓
After replacing the evaporator assembly at the dealership, I noticed the centre screen no longer showed the outside PM2.5 value. Retrieved DTC B110E09. Inspection found that during the dashboard removal, a tool had touched the temperature and humidity sensor probe on the PM2.5 detector, physically damaging the internal humidity-sensitive element. Measured the sensor signal line voltage: constant 4.9 V (normally it should fluctuate between 1–4 V with temperature and humidity changes). Replaced the PM2.5 detector assembly, then performed the 'Air Quality Sensor Learning' function using the diagnostic tool. Live data showed 25 °C and 60% humidity; function returned to normal.
BYD DTC AI Analysis

Prolonged exposure to high humidity caused sensor corrosion

✓
Vehicle used in a coastal city. After 2 years, DTC B110E09 appeared. Removed and inspected the PM2.5 sensor and found obvious salt spray corrosion on the internal circuit board, with oxidised solder joints on the temperature and humidity sensor. The cause was prolonged high-load operation of the air conditioning system combined with coastal humidity, resulting in moisture ingress to the sensor module. After cleaning the corrosion from the circuit board, the fault cleared temporarily, but returned after one week. Replaced the PM2.5 sensor and applied conductive anti-corrosion grease to the wiring harness connector, permanently fixing the fault.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.