NO
AU
B161B-00

DTC B161B-00 indicates the airbag control unit (SRS ECU) detects the front passenger airbag (PAB) igniter circuit resistance is below the calibrated threshold (typically below 1 — Atto 3

Safety System

DTC B161B-00 indicates the airbag control unit (SRS ECU) detects the front passenger airbag (PAB) igniter circuit resistance is below the calibrated threshold (typically below 1.5-2.0Ω, depending on the vehicle software version).

The standard SRS airbag igniter resistance is generally 2.0±0.5Ω.

Low resistance typically indicates a short circuit.

Potential causes include an internal short in the airbag igniter, a wiring harness short to ground, a short between connector terminals, or an internal short in the clock spring.

This fault forces the SRS system into a degraded mode.

The system may disable the front passenger airbag (preventing deployment) or, in extreme cases, risk unintended deployment.

When this DTC triggers, the instrument panel airbag warning light remains illuminated and the system halts collision detection for the front passenger airbag.

4
Cases Logged
Real-World Cases
BYD DTC AI AnalysisFrom Chinese market (translated)

BYD Qin EV300: Internal short circuit in passenger airbag module causing B161B-00

✓
A 2017 Qin EV300 with 80,000 km had the airbag warning light on steady. Scan tool pulled B161B-00 (front passenger airbag resistance too low) – current code. I disconnected the battery negative, waited 90 seconds, and removed the front passenger airbag module. Measured resistance at the module connector: only 0.8 Ω (normal is around 2.0 Ω) – clearly low. The harness side measured 2.1 Ω, within spec, so the fault was an internal igniter short in the module. Replaced the module with a genuine OEM unit, cleared the code, and ran a system self-check. Everything returned to normal, fault gone.
BYD DTC AI AnalysisFrom Chinese market (translated)

Qin 100: Clock spring short caused intermittent B161B-00

✓
2017 Qin 100. The customer reported the airbag warning light illuminating intermittently, especially after turning the steering wheel. The diagnostic tool retrieved current fault code B161B-00. Checked passenger airbag module resistance: normal. Measured clock spring output resistance and found fluctuating values—sometimes reading 0.3Ω (too low), sometimes normal. Disassembled the steering wheel for inspection and found the clock spring's internal flat cable worn from long-term rotation, causing a local short circuit. Replaced the clock spring assembly. After replacement, repeatedly turned the steering wheel to test; the fault did not reappear. Cleared B161B-00 and it has not returned.
BYD DTC AI AnalysisFrom Chinese market (translated)

Qin EV450 dashboard wiring harness chafed, short to ground

✓
2018 BYD Qin EV450. The SRS warning light came on after flood damage repairs. Retrieved DTC B161B-00. Checked below the passenger side dashboard and found the wiring harness retaining clip had detached. The harness had chafed against the metal dashboard bracket, damaging the insulation and causing the wire to short directly to ground. Measured airbag circuit resistance to ground at only 0.5 Ω. Repaired the damaged wiring by rewrapping with insulating tape and fitting corrugated tubing. Rerouted the harness and re-secured the clip. Cleared the fault code; system returned to normal.
BYD DTC AI AnalysisFrom Chinese market (translated)

Water ingress corroded the Qin 80 SRS connector, causing low resistance.

✓
2017 BYD Qin 80. Water accumulated below the front passenger-side A-pillar due to a windshield leak. The SRS warning light came on. Retrieved DTC B161B-00. Found obvious water stains and green copper corrosion inside the yellow SRS wiring harness connector below the A-pillar, with a micro short circuit between terminals. Measured resistance at 1.2Ω (below threshold). Cleaned the connector terminals with electronic contact cleaner, dried them with compressed air, applied conductive anti-corrosion compound, reconnected the connector, and sealed it against water ingress. Cleared the DTC and resolved the fault. Also repaired the windshield seal to prevent further water entry.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.