NO
AU
B16F511

DTC B16F511 indicates an abnormally low-resistance connection between the first signal line (low-side reference line/signal return) of an SRS crash sensor (typically a front or side crash sensor) and body ground — Atto 3

Safety System

DTC B16F511 indicates an abnormally low-resistance connection between the first signal line (low-side reference line/signal return) of an SRS crash sensor (typically a front or side crash sensor) and body ground.

This short to ground causes the SRS control unit (ACU) to detect an abnormal voltage near 0V, preventing it from correctly receiving the sensor acceleration signal.

The system enters fail-safe mode and disables the corresponding airbag deployment function.

In extreme cases, misinterpreting the crash signal may trigger unintended airbag deployment.

This critical circuit fault in the active safety system directly affects the normal protective function of the occupant restraint system.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin Pro petrol: SRS warning after accident repair

✓
2021 BYD Qin Pro petrol. After repairing front-end collision damage, the airbag warning light stayed on. The scan tool retrieved DTCs B16F511 (sensor line 1 short to ground) and accompanying B16F811 (sensor line 2 short to ground). The owner had already replaced the driver and passenger airbags, repaired the airbag control module, and replaced the seatbelts, but the fault persisted. We inspected the wiring harness and found nothing abnormal. We traced the fault to a damaged input stage circuit inside the SRS control unit (ACU), which caused false short-to-ground reports on the sensor lines. Replacing the SRS control unit with a new one and completing the online configuration cleared the fault.
Original source ↗
BYD DTC AI Analysis

BYD E2 airbag warning light came on after driving through water.

✓
2019 BYD E2. Airbag warning light stayed on after driving through water during heavy rain. Diagnosis showed DTC B16F511 pointing to the right front impact sensor. Inspection found the sensor connector located beneath the right front wheel arch liner; the seal had aged, allowing water ingress when wading. Water scale and electrolyte deposits created a short between terminal 1 and body ground. Cleaned the connector interior with compressed air, applied dedicated conductive grease, replaced the waterproof seal, and re-secured the wiring harness. Fault cleared.
BYD DTC AI Analysis

Chafed front compartment wiring harness causing intermittent short circuit in Qin EV

✓
2019 BYD Qin EV. Airbag light comes on occasionally on rough roads, normal on smooth roads. Scan tool retrieved historical DTC B16F511. Found the front impact sensor harness missing a rubber grommet at the edge of a front longitudinal member hole. Prolonged vibration wore through the insulation, exposing the copper conductors and causing the wire to intermittently ground against the chassis. Rewrapped the harness, reinforced with high-temperature insulation tape, installed a dedicated rubber grommet, and adjusted the mounting position. Fault resolved.
BYD DTC AI Analysis

E3 side impact sensor internal short circuit

✓
2020 BYD E3, no accident history. Airbag warning light came on suddenly and could not be cleared. DTC B16F511 pointed to the left B-pillar side impact sensor. Disassembly revealed signs of water accumulation in the sensor mounting hole. The internal piezoelectric element had moisture ingress due to water seepage through the B-pillar trim, causing the signal wire to short to the housing. Replaced with a new side impact sensor, inspected the window seals for aging and applied fresh sealant, and cleared the blocked drain holes. System returned to normal.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.