NO
AU
B1717-00

This DTC indicates the SRS (Supplemental Restraint System) ECU detected an open circuit or disconnected condition in the left knee airbag module (Driver Knee Airbag Module) during self-diagnosis — Atto 3

Safety System

This DTC indicates the SRS (Supplemental Restraint System) ECU detected an open circuit or disconnected condition in the left knee airbag module (Driver Knee Airbag Module) during self-diagnosis.

Specifically, when the SRS ECU sends a test signal to the left knee airbag igniter circuit, it fails to receive a normal circuit response or detects a circuit resistance exceeding the normal threshold (typically infinite or extremely high resistance).

Consequently, the left knee airbag may fail to deploy during a collision, resulting in a loss of lower limb protection for the driver.

Additionally, the SRS enters fail-safe mode and continuously illuminates the instrument cluster airbag warning light.

The system may also lock the deployment function of the entire airbag system, severely compromising passive safety performance.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Loose connector on left knee airbag causing 'not connected' fault

✓
A 2017 BYD Qin EV300's airbag warning light stayed on. Read DTC B1717-00. Found that during a cabin air filter replacement at an independent shop, removing and refitting the lower dash trim had loosened the left knee airbag connector. After firmly reconnecting the connector and confirming the retaining clip was fully seated, cleared the DTC and the system returned to normal.
Original source ↗
BYD DTC AI Analysis

Knee airbag module damaged after accident repair

✓
After front collision repair on a 2017 Qin 100, the SRS warning light stayed on. The diagnostic scanner showed DTC B1717-00. Inspection found the left knee airbag module had not deployed, but impact from the accident caused an open circuit in the internal igniter. The module showed infinite resistance. Replacing the left knee airbag module resolved the fault.
Original source ↗
BYD DTC AI Analysis

Wiring harness chafing caused intermittent open circuit

✓
A 2018 BYD Qin EV450 had an intermittent airbag warning light; fault code B1717-00 would come and go. I found the driver's side knee area wiring harness had chafed through from prolonged steering movement, damaging the insulation and partially breaking some internal copper wires. I repaired the harness and fitted an anti-chafe sleeve, which completely resolved the fault.
BYD DTC AI Analysis

Oxidised connector pins causing poor contact

✓
A high-mileage Qin 80 logged DTC B1717-00 after use in humid conditions. Disassembly inspection found green oxidation on the left knee airbag connector pins, increasing contact resistance (measured 15 Ω; normal: <1 Ω). Cleaned the pins and applied conductive grease. Resistance returned to normal, then cleared the fault code.
Original source ↗
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.