NO
AU
B174B-00

This DTC indicates the firing circuit resistance of the left rear side airbag (typically integrated into the left rear door C-pillar trim panel or the side of the left rear seat backrest) falls below the SRS control module threshold (normal range 2 — Atto 3

Safety System

This DTC indicates the firing circuit resistance of the left rear side airbag (typically integrated into the left rear door C-pillar trim panel or the side of the left rear seat backrest) falls below the SRS control module threshold (normal range 2.0-3.0Ω; fault threshold typically <1.0Ω or near 0Ω).

Low resistance indicates an abnormal low-resistance path in the circuit.

Causes include a short to ground, damaged wiring harness insulation, shorted connector pins, or an internal short in the airbag inflator bridge wire.

This fault forces the SRS system into a degraded mode and illuminates the airbag warning light.

During a collision, the affected airbag may fail to deploy (as the control module detects a short and disables the firing circuit) or, in extreme cases, deploy unintentionally.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin EV450 left rear seat side airbag connector water ingress short circuit

✓
Symptoms: After driving through water, the airbag warning light stayed on. VDS detected active fault code B174B-00. Diagnosis: Removed and inspected the left rear sill trim panel. The side airbag harness connector showed obvious water ingress, with green copper corrosion between the pins. Resistance between pins measured only 0.4Ω (short circuit condition). Solution: Cleaned the connector with anhydrous ethanol and blow-dried it. After drying, harness-to-ground insulation tested normal. Reconnected the connector, applied waterproof silicone grease, and cleared the fault code. Circuit resistance returned to 2.4Ω.
Original source ↗
BYD DTC AI Analysis

BYD Qin 100 rear seat wiring harness wear causing low resistance

✓
Symptoms: Dashboard airbag warning light illuminates intermittently, particularly over rough surfaces. Diagnosis: DTC B174B-00 stored as intermittent fault. Removed left C-pillar trim and found side airbag wiring harness chafing against seat mounting bracket. Damaged insulation caused intermittent short to ground; resistance to ground fluctuated between 0.5-5MΩ. Solution: Repaired damaged wiring with heat shrink tubing and insulating tape, re-secured harness to original retaining clip positions, added corrugated tubing protection. Fault resolved.
Original source ↗
BYD DTC AI Analysis

BYD Qin EV300 airbag module internal short circuit

✓
Symptoms: Airbag warning light stays on continuously; DTC B174B-00 will not clear. Diagnosis: Disconnected the left rear side airbag connector. Resistance across the airbag unit pins measured only 0.6Ω (normal: 2–3Ω), indicating an internal short in the airbag igniter. Harness side resistance to ground measured >10MΩ, normal. Resolution: Replaced the left rear side airbag module (seat backrest removal required). Performed SRS system matching using VDS. After clearing the fault code, resistance reads 2.8Ω, normal.
Original source ↗
BYD DTC AI Analysis

BYD Qin 80: software false alarm and intermittent wiring harness connection

✓
Symptoms: 3-month-old vehicle logged DTC B174B-00. No accident or water submersion history. Diagnosis: Visual inspection of the wiring harness showed no abnormalities. Found slightly backed-out airbag connector pins, causing unstable contact resistance (intermittent low values). The SRS ECU had outdated software. Solution: Re-seated the backed-out pins to ensure full engagement. Updated the SRS control module software to the latest version (optimised resistance sampling algorithm). The fault has not recurred.
Original source ↗
BYD DTC AI Analysis

BYD Qin EV450 seat connector not fully seated after seat removal and refit

✓
Symptom: The owner reported the airbag warning light illuminated after the left rear seat was reupholstered. Diagnosis: Retrieved DTC B174B-00. Inspection revealed the side airbag connector was not fully locked; the internal shorting bar had made unintended contact, causing circuit resistance to drop abnormally to 0.9 ohms. Solution: Reinserted and secured the airbag connector, confirmed the locking tab engaged (audible click), cleared the DTC, and road tested to confirm normal system operation.
Original source ↗
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.