NO
AU
B17771A

DTC B17771A indicates the airbag control unit (SRS ECU) detects a circuit resistance of 0Ω or close to 0Ω for the second-row left seat belt pretensioner — Atto 3

Safety System

DTC B17771A indicates the airbag control unit (SRS ECU) detects a circuit resistance of 0Ω or close to 0Ω for the second-row left seat belt pretensioner.

Normally, the squib resistance inside an undeployed pretensioner is 2.0Ω±0.2Ω.

A resistance of 0Ω indicates a hard short in the circuit.

Potential causes include an internal short in the pretensioner coil, a wiring harness short to body ground, or a short between connector terminals.

This is a safety system hard fault.

The SRS ECU illuminates the airbag malfunction indicator lamp (MIL) and disables the second-row left seat belt pretensioner and potentially associated airbag functions.

During a collision, the pretensioner fails to generate the designed pulling force to tighten the seat belt, reducing occupant restraint protection.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Worn seat rails caused the wiring harness to short to ground

✓
Vehicle: 2020 BYD E3, 32,000 km. Symptom: SRS warning light steady on, DTC B17771A stored. Found the code set intermittently when sliding the left middle row seat fore and aft. Removed the seat; the pretensioner harness had chafed against the seat rail mounting bracket, wearing through the insulation and shorting the copper conductors to ground. Repaired the harness with heat-shrink tubing, rerouted the wiring and added chafe protection. Fault resolved.
BYD DTC AI Analysis

Corroded connectors caused short circuit after water wading

✓
Vehicle: 2019 Qin EV, previously waded through water up to sill height. Fault: Airbag warning light on; diagnostic tool showed left middle row pretensioner resistance at 0 ohms. Repair: Found visible water staining and green copper corrosion inside the yellow connector beneath the left middle row seat, with a conductive layer between terminals causing a short. Cleaned the connector terminals, flushed with electronic contact cleaner and dried, applied conductive protectant, and reinstalled. Recommend inspecting the sealing integrity of other SRS connectors on the vehicle.
BYD DTC AI Analysis

Seatbelt pretensioner squib internal short circuit

✓
Vehicle: 2020 E2, accident-repaired. Fault: DTC B17771A after left middle-row seat replacement. Diagnosis: New seat pretensioner resistance measured 0.2Ω (abnormal). Disassembly found a refurbished pretensioner with partially triggered squib causing internal short. Repair: Installed genuine new pretensioner assembly (part number must match VIN). Fault cleared. Note: Accident repairs require untriggered genuine pretensioners.
BYD DTC AI Analysis

Incorrect wiring of aftermarket seat heating pads caused the fault.

✓
Vehicle: 2019 Qin EV, aftermarket modified. Symptom: DTC B17771A appeared after seat heater installation. Repair: The installer drilled through the seat foam to secure the heating pad, driving the screw straight through the pretensioner harness and shorting positive and negative. Replaced the damaged harness section and repositioned the heating pad to clear the factory wiring. Fault resolved. Note: SRS modifications must strictly avoid yellow wiring harnesses.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.