NO
AU
B17841A

This fault code indicates the SRS control module detects the driver-side front airbag Stage 2 igniter (inflator) circuit resistance at or near 0 ohms, indicating a short circuit (short to ground or short between wires) — Atto 3

Safety System

This fault code indicates the SRS control module detects the driver-side front airbag Stage 2 igniter (inflator) circuit resistance at or near 0 ohms, indicating a short circuit (short to ground or short between wires).

In dual-stage airbag systems, Stage 2 typically provides additional inflation capacity during severe collisions or delays inflation to optimize protection.

A resistance of 0 ohms causes the SRS ECU to determine the igniter circuit is abnormal.

The ECU disables the deployment function of this airbag stage and illuminates the airbag warning light.

In extreme cases, an unstable short circuit creates a risk of unintended airbag deployment, or the airbag stage may fail to inflate normally during an actual collision, reducing protection and severely compromising occupant safety.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin EV clock spring internal wear causing short circuit

✓
The instrument cluster airbag warning light stays on. VDS reads active fault code B17841A. Disconnected the driver airbag module; the second stage igniter resistance measured normal at 2.1Ω. Further testing showed the clock spring's second stage igniter circuit resistance to ground drops to 0.3Ω when the steering wheel is at full right lock. Disassembled the clock spring and found the internal flat cable insulation worn at the winding center; copper foil contacting the metal housing caused an intermittent short. Replaced the OEM clock spring (part number must match the VIN). Fault resolved and system self-test passed.
BYD DTC AI Analysis

E2 model: Internal short circuit in airbag module igniter

✓
After driving through water, DTC B17841A set and would not clear. Clock spring wiring harness insulation checked good; found no shorts. Direct measurement between the driver airbag module Stage 2 igniter pin and metal housing read 0Ω, confirming internal seal failure in the airbag module and a short to ground between the igniter bridge wire and housing. Replaced the driver airbag assembly (includes gas generator and cushion—note Stage 1 and Stage 2 igniter pin definitions). Cleared the DTC and performed a simulated crash test; system functions normally.
BYD DTC AI Analysis

Dashboard wiring harness chafing caused intermittent SRS short circuit

✓
The BYD E3's airbag warning light came on intermittently when driving on rough roads. The scanner showed intermittent fault code B17841A. Disassembly revealed that a dashcam mounting screw had pierced the SRS harness corrugated tube on the instrument panel frame, causing the stage-2 airbag harness copper core to contact the metal frame. Repaired the insulation with high-temp insulation tape and fresh corrugated tube, rerouted the harness to avoid sharp metal edges. Fault eliminated.
BYD DTC AI Analysis

False positive fault in SRS ECU internal sampling circuit

✓
The vehicle had no collision history when DTC B17841A suddenly appeared. Replaced the clock spring and airbag module; fault persisted. Oscilloscope check of the SRS ECU igniter detection pulse waveform revealed internal sampling circuit reference voltage drift, causing the ECU to misjudge normal 2.0Ω resistance as 0Ω short. Replaced the airbag control module (ACU), recoded the vehicle configuration, and calibrated the crash sensors. The system returned to normal and the fault code did not reappear.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.