NO
AU
B17A300

In the BYD SRS system, DTC B17A300 carries two technical indications: 1) The surface description, "seat belt pretensioner collision", indicates the system detects a trigger signal or ignition circuit fault in the driver or passenger seat belt pretensioner (Pyrotechnic Pretensioner); 2) The underlying technical definition, "SRS CAN Signal Abnormal", means the airbag control unit (ACU) loses communication with the vehicle CAN network (typically the powertrain or comfort network) or detects a data checksum error — Atto 3

Safety System

In the BYD SRS system, DTC B17A300 carries two technical indications: 1) The surface description, "seat belt pretensioner collision", indicates the system detects a trigger signal or ignition circuit fault in the driver or passenger seat belt pretensioner (Pyrotechnic Pretensioner); 2) The underlying technical definition, "SRS CAN Signal Abnormal", means the airbag control unit (ACU) loses communication with the vehicle CAN network (typically the powertrain or comfort network) or detects a data checksum error.

This fault forces the airbag system into a degraded mode, potentially preventing airbag and pretensioner deployment during a collision.

It also triggers a continuous airbag warning light on the instrument cluster.

In models such as the Qin PRO, this fault frequently accompanies B17A200 (collision record locked) or B17A400 (hardwired signal abnormal), indicating the vehicle experienced a collision or the CAN bus physical layer has an intermittent fault.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Qin Pro DM SRS warning light on after driving through water, with DTC B17A300

✓
2019 BYD Qin PRO DM, 30,000 km. After driving through heavy flood water, the airbag warning light on the dash stayed on permanently. Scanned DTCs B17A300 and B17A200. Found the waterproof seal on the right front floor harness connector below the A-pillar was damaged. The CAN-H and CAN-L pins had oxidised, causing an intermittent short. Cleaned the oxide layer, applied conductive grease, and replaced the waterproof seal. CAN resistance now measured normal. Performed the collision record clear procedure. Fault resolved.
BYD DTC AI Analysis

Yuan PLUS communication fault caused by unreplaced pretensioner after accident repair

✓
2022 BYD Atto 3. After front collision repairs, the instrument cluster showed 'Safety System Fault'. DTCs: B17A300 (SRS CAN fault) and B165C00 (driver pretensioner open circuit). Inspection found the driver's seat belt pretensioner had deployed in the accident, but the repair shop only replaced the front bumper without replacing the seat belt assembly. The open pretensioner circuit caused the ACU to report a communication fault. Replaced the driver seat belt with force limiter assembly, performed online configuration and calibration. Fault resolved.
Original source ↗
BYD DTC AI Analysis

Qin Pro (Fuel): Loose ACU power supply connection causing intermittent fault

✓
2018 BYD Qin Pro petrol. Airbag warning light illuminated intermittently while driving. Scan tool showed history DTC B17A300. Checked ACU power supply; found ignition voltage dropped below 8V on rough roads. Traced wiring to loose F2/3 fuse holder below the dashboard, causing intermittent ACU reset and CAN communication timeout. Replaced instrument panel distribution box assembly and tightened all connectors. Fault did not recur.
BYD DTC AI Analysis

Software mismatch caused SRS system lockout

✓
After replacing the ACU module at the dealership, the 2019 Qin Pro DM showed an airbag fault on the instrument cluster. Read DTCs B17A300 and U0155 (lost communication with ACU). The new module had the correct part number but software version V1.2; the vehicle requires V2.1 to support the new network architecture. Used the BYD dedicated diagnostic tool to perform online programming, updated the ACU software to the latest version, wrote the VIN, and matched the configuration word. System returned to normal.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.