NO
AU
B178B-00

This fault code indicates that the resistance of the second stage (Level 2, typically the full-power deployment mode for severe collisions) inflator squib in the front passenger airbag dual-stage deployment circuit falls below the safety threshold set by the SRS ECU (generally below 1 — Atto 8

Safety System

This fault code indicates that the resistance of the second stage (Level 2, typically the full-power deployment mode for severe collisions) inflator squib in the front passenger airbag dual-stage deployment circuit falls below the safety threshold set by the SRS ECU (generally below 1.5 Ω).

In BYD dual-stage airbag systems, the first and second stages correspond to different collision severities.

The system achieves staged deployment by controlling different firing circuits.

Low resistance indicates the ECU detects an abnormal drop in circuit impedance and identifies a short circuit fault.

The system enters a safety protection state and disables the airbag to prevent accidental deployment, rendering the airbag inoperative during a collision.

This fault directly affects collision safety protection and requires immediate repair.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin EV300: Connector came loose after dashboard removal and refit, causing B178B-00

✓
A 2017 Qin EV300 showed a constant airbag warning light after the dealership replaced the air conditioning evaporator. VDS retrieved DTC B178B-00. The technician found the passenger airbag harness connector (yellow plug) had not fully seated during dashboard removal and installation, and terminal oxidation caused reduced contact resistance. The technician reseated the connector, treated the terminals with electronic cleaner, and cleared the DTC. The system self-test passed and the fault resolved.
Original source ↗
BYD DTC AI Analysis

BYD Qin 100 airbag module internal short after collision repair

✓
A 2017 Qin 100 sustained a minor frontal impact. External damage was slight and the airbags did not deploy, but the instrument cluster displayed an airbag fault after repairs. Diagnosis revealed DTC B178B-00; measured resistance on the passenger airbag second stage circuit was only 0.6Ω (normal 2.0–3.0Ω). Disassembly revealed the airbag inflator internal bridge wire had deformed from the impact, causing a short to the housing. Replaced the OEM passenger front airbag assembly (part number: ...verify against vehicle specification) and completed system calibration. Fault resolved.
BYD DTC AI Analysis

Qin EV450 intermittent fault from connector oxidation after water wading

✓
A 2018 Qin EV450 developed an intermittent airbag warning light after driving through deep water in heavy rain; the light sometimes cleared after a restart. A VDS scan retrieved historic fault code B178B-00. Inspection revealed damage to the passenger-side floor harness grommet, letting moisture into the airbag harness connector. This reduced insulation resistance between terminals and created a micro-short. Fix: thoroughly cleaned the connector terminals, dried the harness interior with a heat gun, applied waterproof insulating silicone grease to the connector, and installed a waterproof protective sleeve. The fault has not returned.
BYD DTC AI Analysis

Aftermarket modification pinches wiring harness, causing short on Qin 80

✓
A 2017 Qin 80 owner self-installed a Head-Up Display (HUD), routing the wiring through a dashboard gap and accidentally pinching the passenger airbag harness. After some time, the airbag warning light illuminated with DTC B178B-00. Inspection found the harness insulation chafed against the dashboard metal bracket, causing the second-stage trigger wire to short to ground. The repair involved fixing the damaged harness (replacing the entire section or wrapping locally), repositioning the HUD wiring to avoid the airbag harness, and clearing the fault codes. The system then returned to normal.
Other Atto 8 Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.