NO
AU
B132012

DTC B132012 indicates a short to power in the left front seat heater circuit (DTC structure: B13 = Seat Control Module (SCM) system, 20 = left front seat heater, 12 = short to power) — Qin Plus

Thermal Management System

DTC B132012 indicates a short to power in the left front seat heater circuit (DTC structure: B13 = Seat Control Module (SCM) system, 20 = left front seat heater, 12 = short to power).

The Seat Control Module triggers this code when it detects an abnormally low-resistance path between the heater pad circuit and the vehicle power supply (B+).

This fault causes the seat heating function to fail, the heater pad to overheat, and may produce a burning smell.

Severe cases can blow the associated fuse or damage the control module.

This fault falls under the body electrical system and has no relation to the coolant temperature sensor described in the original documentation (Note: some reference materials contain classification errors; this is strictly a seat system fault).

3
Cases Logged
Real-World Cases
BYD DTC AI AnalysisFrom Chinese market (translated)

BYD Qin Pro DM left front heated seat inoperative.

✓
Symptom: Left front seat heater does not turn on. Indicator light off. Diagnosis: Scanned with VDS2000 and retrieved DTC B132012. Measured infinite resistance at the heating pad. Found seat base harness rubbing against frame; power wire insulation worn through and shorted. Resolution: Repaired harness, rerouted wiring, cleared fault codes. Seat heating function restored.
Original source ↗
BYD DTC AI AnalysisFrom Chinese market (translated)

BYD Song MAX seat heating system fault

✓
Symptoms: After replacing the seat foam, the heating function failed and the indicator light flashed then went out, with DTCs B132012 and B132014 stored. Diagnosis: Inspection found pin 14 of the G09 connector had backed out, causing abnormal signals; the CAN communication interruption was a false alarm. Resolution: Repaired the backed-out pin, recalibrated the seat control module, and cleared the fault codes.
Original source ↗
BYD DTC AI AnalysisFrom Chinese market (translated)

BYD Tang DM seat heater short circuit fault

✓
Symptoms: Seat heating stopped suddenly with a burnt smell. Stored fault code B132012. Diagnosis: Heating pad partially burnt, with abnormal resistance. MOSFET inside control module shorted. 12V power cable under seat aged and damaged, shorted to signal wire. Fix: Replaced heating pad assembly, control module, and damaged wiring harness, then reprogrammed.
Original source ↗
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.