NO
AU
B163212

DTC B163212 indicates a short to battery positive (B+) in the front passenger seat side airbag ignition circuit — Qin Plus

Safety System

DTC B163212 indicates a short to battery positive (B+) in the front passenger seat side airbag ignition circuit.

Technically, this means an abnormal connection to the permanent 12V supply exists in the wiring harness or connectors between the airbag control module (SRS ECU) and the front passenger seat side airbag.

Normally, the airbag igniter terminals maintain a high resistance (>10kΩ) in the non-deployed state or only receive a low-current monitoring signal from the ECU.

A short to power causes the following: 1) The SRS system enters protection mode, cutting power to this circuit to prevent unintended deployment; 2) The front passenger seat side airbag completely fails, preventing deployment during a side impact; 3) A potential unintended deployment risk arises.

Although the ECU typically features short-circuit protection, a continuous short to power can overheat and damage the control module's internal driver chip.

ISO 26262 classifies this fault as a high Automotive Safety Integrity Level (ASIL D) fault, requiring immediate resolution.

5
Cases Logged
Real-World Cases
BYD DTC AI AnalysisFrom Chinese market (translated)

Seat rail wiring harness chafing caused intermittent short circuit.

✓
Symptoms: The airbag warning light on the instrument panel of a 2019 BYD Qin Pro EV illuminated intermittently, more often on bumpy roads. Diagnosis: Using VDS, we retrieved DTC B163212 (current fault). After disconnecting the yellow connector beneath the passenger seat, we measured intermittent continuity between terminal 2 on the harness side and vehicle power. Disassembly revealed the seat rail mounting bolt had compressed the wiring harness sheath; prolonged friction exposed the copper conductors, which then contacted the seat frame (earth) and the adjacent seat heating power line (+12V) simultaneously, creating a short circuit. Solution: We repaired the damaged harness, rerouted it to avoid the seat rail travel area, and secured it with dedicated harness retention clips. This cleared the fault.
BYD DTC AI AnalysisFrom Chinese market (translated)

Corroded connectors caused a short circuit after driving through water

✓
Symptoms: After wading through water in heavy rain, the BYD E2 instrument cluster displayed 'Please check airbag system'. The air conditioning drain hose had blocked, causing water to pool on the front passenger floor. Diagnosis: Inspection found visible water staining and green copper corrosion inside the yellow SRS connector beneath the front passenger seat. A multimeter measured resistance between terminals below 1Ω, indicating a severe short circuit. Disassembly revealed a deteriorated connector seal that allowed water to enter during wading. Fix: Cleaned the connector terminals thoroughly with electrical contact cleaner, blew them dry, and applied dedicated conductive paste. Replaced the waterproof seal, cleared the body drain holes, and dried the affected area for 72 hours before reassembly. Cleared the fault codes; the fault has not returned.
BYD DTC AI AnalysisFrom Chinese market (translated)

Aftermarket seat heater installation caused a wiring short circuit

✓
Symptoms: The BYD E3 owner installed a seat heating pad, causing the airbag warning light to stay on continuously. Diagnosis: DTC B163212 retrieved. The installer had cut open the SRS harness insulation under the passenger seat to tap power, and incorrectly connected the heater pad power wire (constant power) in parallel with the airbag harness, creating a direct short to power in the airbag circuit. Solution: Removed the non-OEM wiring. Repaired the damaged SRS harness using soldering and heat-shrink tubing to ensure contact resistance under 1Ω. Restored the factory wiring layout. Replaced the airbag connector that might have been damaged by the short. Fault resolved, and the owner was informed of the risks of unauthorized modifications.
BYD DTC AI AnalysisFrom Chinese market (translated)

SRS control module internal driver circuit fault

✓
Symptoms: After replacing the passenger airbag assembly on a Qin Pro DM, DTC B163212 remained present and would not clear. Diagnosis: Disconnected the airbag connector and measured no short to power on the harness side. Measured the airbag assembly resistance at 2.3Ω (within normal range). Then measured at the SRS ECU output and found the circuit outputting a continuous 12V (normal: 0V or a very low monitoring voltage). Determined the ignition driver transistor inside the control module had shorted due to breakdown. Solution: Replaced the airbag control module (ACU). Used VDS to perform module coding, matching, and system configuration. Performed crash sensor zero-point calibration. Cleared the DTC and the system returned to normal.
BYD DTC AI AnalysisFrom Chinese market (translated)

B-pillar trim panel clip pinched the wiring harness, causing a short circuit.

✓
Symptom: The vehicle displayed DTC B163212 after interior trim panel removal and refitting. Diagnosis: Inspection found that during installation of the passenger-side lower B-pillar trim panel, the mounting clip position had shifted and punctured the SRS wiring harness insulation. This caused the internal copper wire strands to contact the body power line (supplying the B-pillar ambient lighting). Resolution: Repaired the damaged harness and replaced the punctured wire (both wires in the same circuit were replaced simultaneously to maintain impedance matching). Readjusted the trim panel clip position, fitted a wiring harness protective sleeve, and reinstalled the trim. The fault cleared after reassembly.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.