NO
AU
B169517

DTC B169517 indicates the airbag control unit (SRS ECU/ACU) detected an anomaly during internal self-check, usually pointing to a fault in the ECU internal processor, memory, or power management module — Qin Plus

Safety System

DTC B169517 indicates the airbag control unit (SRS ECU/ACU) detected an anomaly during internal self-check, usually pointing to a fault in the ECU internal processor, memory, or power management module.

In the BYD diagnostic protocol, sub-code '17' specifically indicates an internal ECU circuit fault or a logic error resulting from supply voltage exceeding the threshold.

When the SRS ECU detects an internal oscillator fault, EEPROM data checksum failure, ADC conversion error, or watchdog reset, it sets this code and enters degraded mode.

This mode may disable some or all airbag deployment functions.

Because the ECU is the core of the passive safety system, this fault presents a severe safety risk and can prevent normal airbag deployment during a collision.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Low battery on Qin Pro DM caused SRS ECU low voltage fault.

✓
Vehicle: 2019 BYD Qin Pro DM. Symptom: SRS warning light continuously illuminated on the instrument cluster. Scan tool retrieved active DTC B169517. Repair procedure: The vehicle had been stationary for an extended period, causing the battery voltage to drop to 10.8 V. The owner jump-started the vehicle, after which the fault appeared. SRS ECU supply voltage dropped to 8.5 V during cranking. Installed a new battery and cleared the fault codes. The fault did not return. Analysis: Low voltage caused abnormal operation of the internal reset circuit within the ECU, triggering a self-test fault. Recommendation: For vehicles left stationary for extended periods, disconnect the negative battery terminal or charge regularly to prevent low voltage from causing the ECU to store fault codes.
BYD DTC AI Analysis

BYD E2 SRS ECU internal short circuit after water ingress

✓
Model: 2020 E2 EV. Symptoms: After heavy rain, water leaked into the cabin carpet, the SRS warning light illuminated, and DTC B169517 stored, which could not be cleared. Repair: Removed the centre console and found obvious water stains on the SRS ECU housing. Connector CA1 had green corrosion inside. Disassembled the ECU and found PCB corrosion and shorted main chip pins. Replaced the SRS ECU assembly and treated the harness connector: cleaned it with precision instrument cleaner and sprayed it with contact protector. Also cleared the blocked air conditioning drain tube (the cause of the leak). Performed sensor calibration after replacement. Fault resolved.
BYD DTC AI Analysis

Loose SRS ECU connector causes intermittent fault on Qin EV

✓
Vehicle: 2019 Qin EV. Symptoms: SRS warning light occasionally illuminated while driving, extinguishing after turning the vehicle off and back on. The diagnostic scanner showed stored fault code B169517. Repair process: Inspection found the fault mostly occurred on rough roads. Removed the centre console and inspected SRS ECU connector CA1, finding the connector lock loose and pin 5 (power) slightly backed out. Resolution: Repaired the pin, secured the connector using a special retaining clip, and wrapped waterproof tape around the connector to prevent it from loosening. Cleared the fault codes and test-drove the vehicle for 50 kilometres; the fault did not recur.
BYD DTC AI Analysis

E3 software calibration error caused internal ECU fault code

✓
Model: 2020 E3. Symptoms: Following accident repairs (replacement of the front bumper and wiring harness), the SRS warning light remained illuminated, and DTC B169517 was stored. Repair: Checked the wiring harness connections and power supply voltage — both were normal. Identified that the replacement bumper harness was a non-genuine part, causing abnormal impedance in the left front crash sensor and indirectly triggering internal ECU communication errors. Replaced the crash sensor wiring harness with a genuine part, then used VDS2000 to refresh the software and rewrite the configuration on the SRS ECU (specifically the sensor configuration parameters). After the refresh, cleared the fault code and the system returned to normal.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.