NO
AU
B176E12

DTC B176E12 indicates abnormal continuity between the left rear seat belt pretensioner circuit and the vehicle power supply (B+), representing a "short to power" — Qin Plus

Safety System

DTC B176E12 indicates abnormal continuity between the left rear seat belt pretensioner circuit and the vehicle power supply (B+), representing a "short to power".

In the Supplemental Restraint System (SRS), the seat belt pretensioner is a pyrotechnic actuator.

Under normal conditions, its circuit must remain isolated from the power supply; the SRS ECU supplies a momentary high-current ignition signal only during a collision.

A short to power indicates: 1) continuous battery voltage across the pretensioner terminals risks accidental deployment (extremely dangerous); 2) the SRS ECU detects circuit voltage above the threshold (typically >5V or near 12V) and registers a severe fault; 3) the system immediately illuminates the airbag warning light and disables the entire airbag system (including front and side airbags), leaving the vehicle without collision protection.

This fault involves the left rear seat belt pretensioner (typically located at the lower B-pillar or on the seat frame).

The circuit comprises the ignition loop routing from the SRS ECU through the floor harness to the left rear seat.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Worn seat track on Qin Pro DM chafed wiring harness, causing short circuit

✓
2019 BYD Qin Pro DM, 42,000 km. Airbag warning light stays on. VDS read DTC B176E12 (current fault). Removed left rear sill trim; found seatbelt pretensioner harness chafed against the sharp edge of the seat runner with the seat fully forward. Worn insulation let copper strands touch the seat heater power wire (red 12V constant). Repair: Cut out the damaged harness section, soldered and heat-shrunk, rerouted wiring to clear the seat runner travel path, and added a harness clip at the B-pillar. Cleared the fault and monitored for one month with no recurrence.
Original source ↗
BYD DTC AI Analysis

BYD Song Pro: B-pillar connector shorted after water ingress during wading

✓
2020 BYD Song Pro. Airbag warning light illuminated the day after wading through heavy rain. Diagnosis revealed intermittent codes B176E12 and B17611. Inspection found significant water staining and verdigris inside the left rear B-pillar pretensioner connector (yellow 2-pin); the connector seal had degraded. Root cause: Left rear sunroof drain hose detached, letting rainwater run down the A-pillar into the B-pillar. Repair: Replaced connector terminals (P/N BYD-SRS-PLUG-02), cleaned the wiring harness, reinstalled the drain hose and tested sealing, applied conductive grease to protect the terminals. Also checked floor pan drain holes for blockages.
Original source ↗
BYD DTC AI Analysis

Bent connector pins following E2 accident repair

✓
2021 BYD E2. Left rear seatbelt assembly replaced at a non-authorised shop after a minor collision to the left rear. DTC B176E12 set immediately on pickup. Inspection revealed the pretensioner connector was not fully locked; forced insertion had bent one internal pin (power side) against the adjacent pretensioner ignition terminal, creating a short to power. Fix: Repaired the terminal using a dedicated extraction tool, aligned the connector guide slot, and reconnected until a distinct click confirmed locking. Cleared the code and monitored the pretensioner circuit voltage waveform with an oscilloscope, confirming no abnormal 12V pulses.
Original source ↗
BYD DTC AI Analysis

Tang DM Pretensioner Internal Short Circuit Replacement Case

✓
2018 BYD Tang DM, no collision history. Intermittent airbag warning light, code B176E12 (intermittent). Multiple harness checks found no wear; connectors dry, uncorroded. Disconnected pretensioner plug: harness side showed no short to power. Measured 0.5Ω between pretensioner terminals and housing (should be infinite). Internal igniter insulation failed, causing short to housing (ground). Repair: Replaced left rear seatbelt pretensioner assembly (Part No. BYD-SRS-LR-18). After replacement, used VDS to perform 'Replacement Equipment Identification' and 'Configuration Write' so the SRS ECU learns the new pretensioner resistance.
Original source ↗
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.