NO
AU
B1774-00

This DTC indicates a short to vehicle power positive (B+) in the right rear seat belt pretensioner ignition circuit — Qin Plus

Safety System

This DTC indicates a short to vehicle power positive (B+) in the right rear seat belt pretensioner ignition circuit.

In the BYD SRS (Supplemental Restraint System) architecture, the seat belt pretensioner is a pyrotechnic actuator.

Its normal operating resistance is 2.0-3.0 Ω, and the circuit must remain isolated from the vehicle power supply.

When the SRS ECU detects an abnormal resistance drop (near 0 Ω) or a short to power in this circuit, it triggers DTC B1774-00 and enters fail-safe mode.

This fault prevents the right rear seat belt pretensioner from tensioning normally during a collision.

In extreme cases, short-circuit current may cause the pretensioner to deploy unintentionally, presenting a severe safety hazard.

The system illuminates the airbag warning lamp and may disable the entire right-side airbag system.

3
Cases Logged
Real-World Cases
BYD DTC AI Analysis

C-pillar trim panel retaining clip crushed through wiring harness, causing short circuit

✓
A 2018 Qin EV450’s airbag warning light suddenly illuminated while driving. The scan tool retrieved DTC B1774-00. Removing the right rear C-pillar trim revealed a retaining clip installed off-centre had pierced the yellow SRS wiring harness sheath. The exposed copper wire contacted the clip (which connects to battery positive via the body), creating a short to power. Replaced the damaged SRS harness section (approx. 30 cm), reinstalled the C-pillar trim clip correctly, and reinforced the wiring protection with electrical tape. Fault cleared.
BYD DTC AI Analysis

Water entered during rear window tinting, corroding connectors and causing a short circuit.

✓
2017 BYD Qin 100 airbag warning light stayed on after rain. Found standing water in the right rear seatbelt pretensioner connector (under the seat) with green corrosion on the terminals. Traced to previous window tinting work that let water into the C-pillar; the connector seal had also aged. Repair: Cleaned the terminals with electronic contact cleaner and a specialized brush, replaced the waterproof seal, tested the pretensioner (passed), cleared the fault codes. System back to normal.
BYD DTC AI Analysis

Power supply line incorrectly connected during aftermarket heated rear seat installation

✓
A 2017 Qin EV300 developed a B1774-00 DTC after rear seat heaters were installed. Technicians found the installer had incorrectly tapped the heater power into the SRS pretensioner wiring, leaving the pretensioner circuit continuously powered with excessive current. We removed the unauthorized wiring, replaced the heat-damaged pretensioner harness (insulation melted), recoded the SRS ECU, and restored factory wiring. Fault cleared.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.