NO
AU
B2A7A12

This DTC indicates the heater core 4-way water valve drive motor control circuit has shorted to the vehicle power supply (B+, typically 12V or a 5V reference voltage, depending on the specific drive circuit design) — Qin Plus

Thermal Management System

This DTC indicates the heater core 4-way water valve drive motor control circuit has shorted to the vehicle power supply (B+, typically 12V or a 5V reference voltage, depending on the specific drive circuit design).

When the HVAC ECU or thermal management controller sends a PWM drive signal to the stepper or DC motor, it detects the motor feedback or drive circuit voltage remains continuously high (close to battery voltage).

This exceeds the normal range; normal operation requires a pulsed voltage or ground return path.

This prevents the controller from driving the 4-way water valve to switch the coolant flow direction, affecting the switch between the cabin PTC heating loop and the battery/motor cooling loop.

In severe cases, this fault causes the drive chip to overheat and fail or the related fuse to blow, which triggers the thermal management system protection mechanism and limits power output.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Qin EV front compartment wiring harness wear causing intermittent short circuit

✓
A 2019 BYD Qin EV frequently logged DTC B2A7A12 after driving on rough roads, with intermittent loss of cabin heat. Inspection found the left front 4-way water valve motor harness had chafed against an AC pipe clip, wearing through the insulation to expose copper wires that contacted an adjacent red constant-power B+ harness. The wires separated when cold due to body vibration, but shorted when hot or over bumps. Re-wrapped the damaged harness, rerouted it clear of sharp edges, and fitted abrasion protection sleeving. Fault resolved.
BYD DTC AI Analysis

Water entered the motor causing internal corrosion and a power supply short circuit.

✓
AC system failed after the vehicle waded through water. Scanned DTC B2A7A12. Removed and inspected the four-way water valve and found it mounted low. The aged motor seal leaked during water ingress, corroding the internal PCB and coil terminals. Resistance between the power terminal and motor drive terminal dropped to 0.5Ω (normal should be open circuit). The motor is an integrated assembly and cannot be disassembled for repair, so replaced the heater core four-way water valve assembly with a new unit, ran water valve position self-learning using the diagnostic tool, and cleared the fault.
BYD DTC AI Analysis

Aftermarket heater miswiring caused fault

✓
Owner fitted an aftermarket seat heater. When tapping power from the engine bay fuse box, they mistakenly connected the live wire to the signal feedback line of the four-way water valve motor. This caused 12V to back-feed directly into the motor drive port of the air conditioning controller when the vehicle started, triggering short-circuit protection and logging a DTC. Technicians found the controller driver chip burned out (charring visible on the surface). Fix: Removed the unauthorised wiring, repaired the harness, and replaced the air conditioning controller assembly. Fault resolved.
BYD DTC AI Analysis

Connector seal failure caused short circuit from condensation

✓
The vehicle set this DTC frequently during the rainy season but operated normally in dry weather. Inspection found the seal missing from the four-way water valve motor connector near the firewall in the front compartment. Rainwater tracked along the wiring harness into the connector, forming a water film between the terminals that shorted the power pin to the motor pin. Dried the connector with compressed air, applied dielectric grease, and installed a new connector with a seal. The fault has not returned.
BYD DTC AI Analysis

Controller software false positive (phantom fault)

✓
The vehicle showed no actual fault symptoms, but the scan tool displayed DTC B2A7A12. Measured the motor and wiring harness—both normal. Supply voltage 12.4V, motor resistance 80Ω (within spec). Found the battery management system had been upgraded previously, likely affecting HVAC controller communication. Flashed the HVAC controller to software version V2.3.1 and performed a Network Configuration Reset. Cleared the fault code and it has not returned; determined this was a software false positive.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.