NO
AU
B2A7B92

DTC B2A7B92 indicates the actuator motor for the heater core (PTC heater assembly) 4-way valve cannot reach the target position — Qin Plus

Thermal Management System

DTC B2A7B92 indicates the actuator motor for the heater core (PTC heater assembly) 4-way valve cannot reach the target position.

A stepper or DC motor drives the valve, changing the valve core position to switch coolant flow direction (e.g., directing heat to the heater core, battery heater, or bypass circuit).

The ECU monitors the actual valve opening via a position sensor (potentiometer or Hall effect sensor).

The ECU sets this fault when the deviation between the commanded position and the actual feedback position exceeds the calibrated threshold (typically 5%-10%), or when the motor drive current continuously exceeds the stall protection value (approximately 600-800mA) for 2-5 seconds.

This fault prevents the thermal management system from distributing heat as required, resulting in poor cabin heating, limited charging power at low battery temperatures, or abnormal coolant circulation.

It does not directly affect high-voltage safety.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Qin EV high voltage interlock intermittent connection caused misdiagnosis (Note: actually communication DTC, case retained for reference)

✓
Symptoms: BYD Qin/Tang series. Dashboard displays "Check power system" or "Check charging system" warnings. Vehicle fails to charge or suddenly loses power while driving. Fault code B2A7B92. Diagnosis: Technician retrieved B2A7B92 with a scan tool. Per BYD workshop manual, inspected the high-voltage interlock loop and found burnt interlock pins with poor contact inside the high-voltage service disconnect (MSD). Also found the CAN communication harness between OBC and BMS had insulation deterioration from engine bay heat, causing intermittent signal interruption. Solution: Replaced the high-voltage service disconnect (MSD), re-wrapped and secured the OBC-BMS CAN communication harness, and cleared fault codes. Vehicle returned to normal.
BYD DTC AI Analysis

Qin DM charging communication fault (Note: should actually be a communication class DTC; case retained for reference)

✓
Symptoms: 2016 BYD Qin DM. Frequent interruptions during AC slow charging; instrument cluster showed charging fault. DTC B2A7B92. Diagnosis: Verified fault on arrival—warning lamp lit intermittently during charging. Connected VDS2000 and read DTC B2A7B92. Checked OBC low-voltage supply and ground: normal. Measured CAN-H at 2.6V and CAN-L at 2.4V, essentially normal. Inspected OBC high-voltage input and found poor contact in the HV harness interlock loop between HV distribution box and OBC. This caused BMS to detect HV interlock fault and cut charging. Resolution: Removed HV distribution box, cleaned oxides from HV harness interlock terminals, retightened connections, and applied conductive paste to prevent further oxidation. Updated BMS software to latest version to optimize communication fault tolerance.
Original source ↗
BYD DTC AI Analysis

e5 fast-charging wiring harness wear (Note: actually communication fault codes, case retained for reference)

✓
Symptoms: BYD e5 pure-electric taxi, approximately 120,000 km. Fast charging failed; charging station displayed connection timeout, instrument cluster indicated powertrain fault. Retrieved DTCs including B2A7B92. Diagnosis: Technician connected diagnostic tool and found B2A7B92 among other DTCs. Per BYD e5 workshop manual, CC1 and CC2 signals at the fast charging port were normal. Measured fast charging CAN bus resistance at 60 Ω (normal), but the reading fluctuated when wiggling the harness. Further inspection revealed the harness mounting bracket behind the fast charging port had broken, allowing the fast charging high-voltage harness to chafe against the body metal edge. Damaged harness insulation caused an intermittent short in the CAN signal. Repair: Replaced fast charging port assembly and damaged harness, rerouted the wiring and added protective sleeving, ensuring safe clearance from metal body panels. Fast charging function returned to normal.
Original source ↗
BYD DTC AI Analysis

BYD Song DM wiring harness assembly defect (Note: actually a communication DTC; case retained for reference)

✓
Symptoms: BYD Song DM, 3 months in service. Intermittent failure to energize the high-voltage system; instrument cluster displayed "Check Power System". The fault occasionally cleared after shutting down and restarting. DTC B2A7B92 stored. Diagnosis: Due to the intermittent nature, the technician used the wiggle test to isolate the fault. DTC B2A7B92 indicated a communication error between the BMS and high-voltage distribution box. The BMS power supply, ground and CAN wiring connections tested normal. During inspection, pressing the inner right front fender area reproduced the fault. Disassembly revealed a fender mounting bolt had pinched the wiring harness during assembly, partially fracturing the internal copper wires and creating an intermittent open circuit. Solution: Repaired the damaged wiring harness, rerouted it to clear the fender mounting bolt, and secured it with dedicated harness clips to ensure correct routing.
Original source ↗
BYD DTC AI Analysis

Han EV charging station interference (Note: actually a communication DTC, case retained for reference)

✓
Symptoms: BYD Han EV. Frequent charging faults during home charging. Mobile app displayed "charging interrupted", instrument cluster warning light illuminated, scanner read DTCs B2A7B92 and B2A8A00. Diagnosis: Technician identified B2A7B92 as BMS-OBC communication fault and B2A8A00 as charging system insulation fault. Measured charging system insulation resistance normal, then focused on communication issue. Oscilloscope monitoring CAN bus waveform revealed numerous interference pulses during charging. Traced to poor grounding at home charger and charging cable routed parallel to household air conditioning power line. Electromagnetic interference disrupted CAN communication. Vehicle also ran outdated OBC software with insufficient noise immunity. Resolution: Advised customer to fix charger grounding and reroute charging line away from high-power appliance wiring. Updated OBC and BMS software to latest versions at workshop, optimising CAN communication filtering algorithms. Charging stability improved significantly after repair.
Original source ↗
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.