NO
AU
P056216

P056216 is a BYD IPB (Intelligent Power Brake) extended fault code — Qin Plus

Braking System

P056216 is a BYD IPB (Intelligent Power Brake) extended fault code.

It indicates the IPB control module detects its supply voltage remaining continuously below the internal threshold (typically 9V-10V; normal operating voltage is 12V±0.5V).

As the core brake-by-wire component, the IPB provides electro-hydraulic brake assist, coordinates energy recovery, and controls ESC and ABS functions.

Insufficient supply voltage reduces brake assist motor torque, causing a stiff brake pedal and extended braking distances.

This condition can also degrade or deactivate ESC and ABS functions, severely compromising driving safety.

This fault code typically triggers the IPB warning light, the ABS warning light, and a "Please check the braking system" message.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Song Plus DM-i IPB power supply connector pin backed out causing intermittent brake fault

✓
While driving, the instrument cluster intermittently displayed "Brake System Fault". Both the IPB and ABS warning lights came on together and the brake pedal went hard. Scanned with a diagnostic tool and retrieved codes P056216 (System Voltage Low) and C123456 (IPB Power Supply Abnormal). Freeze frame data showed 8.1V at the time of the fault. Measured voltage at IPB connector pin A-1 (constant power) and found it swinging between 8V-12V while wiggling the wiring harness. Disassembled the IPB connector and found pin 1 (thick red wire) had backed out—the internal latch had broken, allowing the pin to retract. Fix: Used a special pin removal tool to re-crimp the pin. Replaced the IPB wiring harness connector (Part No.: GJ-XXX-XXXX) and seated the pin fully. Voltage stabilized and the fault cleared.
Original source ↗
BYD DTC AI Analysis

Burnt relay contacts inside the front compartment power distribution box caused IPB undervoltage

✓
After parking overnight, the owner reported a brake system fault and DTC P056216 on morning startup; the warning light cleared after driving. The low voltage battery voltage was normal but dropped to 9.8V during startup. Voltage at the IPB fuse output measured only 10.2V with the key ON, while the distribution box input (B+) showed 12.4V—a 2.2V drop. Inspection of the front compartment distribution box revealed severely burnt and blackened contacts on the IPB power relay, with contact resistance of 0.8Ω. Replaced the front compartment distribution box assembly (part number: SA-XXX-XXXX) and checked the IPB module for internal shorts causing excessive current. Post-replacement voltage at the IPB measured 12.3V; fault resolved.
Original source ↗
BYD DTC AI Analysis

Degraded low-voltage AGM battery triggers P056216 during cold start

✓
2021 Song PLUS DM-i. Two years in, the dash threw "Check Brake System" on cold starts. Scanned P056216. Fault appeared whenever ambient temp dropped below 10°C and cleared once warm. Static battery voltage measured 12.1V (low). CCA down to 45% of rated, SOH 60%. Cranking crashed voltage to 8.5V—below IPB threshold. Root cause: owner only took short trips with Battery Intelligent Charging off, so the battery sulfated from chronic undercharge. Fix: Replaced with genuine 60Ah AGM (E6A-XXX-XXXX), turned on Battery Intelligent Charging via the scan tool, and advised the owner to fully charge every two weeks. Cold start voltage now holds above 11.2V. Fault hasn't returned.
Original source ↗
BYD DTC AI Analysis

Oxidized body ground point caused intermittent IPB undervoltage

✓
When driving on rough roads, the instrument cluster intermittently flashed the brake warning light. The scanner showed P056216 as an intermittent fault. IPB supply voltage was normal, but checking the ground circuit revealed a 0.3V drop between the IPB housing and battery negative terminal, with unstable resistance. Found the G302 ground point on the left front longitudinal member had a loose ground wire bolt, plus white oxide and paint residue on the contact surface. Repair: Removed the ground wire, sanded the contact surface to bare metal with 80-grit sandpaper, applied conductive paste (not grease), and torqued the bolt to 9N·m. Also inspected the IPB housing ground wire (black heavy-gauge cable) ring terminal for cracks. After repair, ground voltage drop measured under 0.05V. Road-tested 50 km with no fault recurrence.
Original source ↗
BYD DTC AI Analysis

Unstable DC-DC converter output caused low system voltage while driving

✓
Driving in EV mode with headlights and A/C on, the instrument cluster showed a brake system fault. DTCs P056216 and U01A987 (IPB communication fault) appeared simultaneously. Battery voltage dropped instantly from 13.8V to 9.5V when high-power loads came on, fluctuating constantly. At the DC-DC low-voltage output terminals, voltage was unstable, oscillating between 12V and 14V. The scan tool showed a history of 'low-side overcurrent protection' in the DC-DC data stream. Inspection found an internal loose connection in the positive harness from the DC-DC converter to the battery (runs through the front compartment fuse box). Fix: Replaced the harness from the DC-DC to the fuse box (including fuse) and flashed the DC-DC control software to V2.3.5 or above. Post-repair load testing confirmed voltage stable at 13.5V±0.2V. Fault resolved.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.