NO
AU
B1698-00

B1698-00 indicates the airbag system electronic control unit (SRS ECU) detects an internal fault or critical function abnormality — Seal 6 EV

Safety System

B1698-00 indicates the airbag system electronic control unit (SRS ECU) detects an internal fault or critical function abnormality.

This fault code typically indicates an SRS ECU internal memory error, processor fault, power supply voltage out of operating range (overvoltage or undervoltage), or a persistent communication bus fault between the ECU and the crash sensors or airbag modules.

In BYD Qin series vehicles, this fault forces the airbag system into fail-safe mode and continuously illuminates the instrument panel airbag warning lamp.

During a collision, the vehicle may fail to deploy the airbags and seat belt pretensioners, posing a severe safety hazard.

This fault code is a hard fault that does not clear automatically and requires professional diagnosis and repair.

3
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Qin EV300 airbag warning light suddenly came on while driving.

✓
Vehicle: 2017 Qin EV300, 42,000 km, no accident history. Symptoms: Airbag warning light suddenly illuminated during normal driving. VDS read DTCs B1698-00 (SRS ECU fault) and B1694-00 (power supply voltage low). Diagnosis: Measured SRS ECU power supply terminals and found IG power voltage fluctuating between 8.5V and 11V — abnormal. Traced the wiring harness and discovered a loose harness retaining clip under the dashboard. The harness had been rubbing against the steering column metal bracket over time, damaging the insulation and partially breaking the copper wires, causing high resistance. Repair: Repaired the damaged harness, re-secured the harness routing, and measured voltage restored to 12.4V. Cleared fault codes, the airbag light went out, and the system returned to normal.
BYD DTC AI Analysis

BYD Qin 100 SRS failure after wading though water

✓
Vehicle: 2017 BYD Qin 100. After driving through heavy rain and floodwater, the instrument cluster displayed "Check Airbag System." Symptoms: The vehicle waded through approximately 30 cm of water. The airbag warning light then stayed on constantly. The scan tool showed active fault code B1698-00. Diagnosis: Removed the SRS ECU from beneath the centre console. The ECU housing seal had deteriorated, with visible water stains and oxidation on the circuit board. Measured ECU power supply: normal, but the internal CAN transceiver pins were shorted to earth. Solution: Fitted a new SRS ECU (part number: BYDEG-3658100). Replaced the wiring harness seal. Dried and applied corrosion protection to the surrounding wiring harness. Performed ECU coding. Fault resolved.
BYD DTC AI Analysis

Intermittent B1698-00 fault on Qin EV450

✓
Vehicle: 2018 Qin EV450. Fault intermittent, more likely during cold starts. Symptoms: The airbag warning light occasionally came on during morning startup and sometimes went off after driving for a while. VDS scan showed historic DTC B1698-00. Diagnosis: During continuous monitoring, I found the SRS ECU earth voltage was 1.2V when the fault occurred (normal: <0.1V). I inspected the earth wire and found the earth point beneath the A-pillar. The mounting bolt was loose, and the contact surface had paint and oxidation. Repair: I sanded the earth point contact surface to bare metal, reinstalled the earth bolt, and tightened it to standard torque (typically 8-10N·m). Earth resistance dropped to 0.3Ω after the repair. I monitored the vehicle for a week; the fault did not return.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.