NO
AU
B178A1A

DTC B178A1A indicates the SRS control module detects the Passenger Second Stage Front Airbag igniter circuit resistance at or near 0 ohms — Seal 6 EV

Safety System

DTC B178A1A indicates the SRS control module detects the Passenger Second Stage Front Airbag igniter circuit resistance at or near 0 ohms.

The second-stage airbag uses dual-stage ignition technology to control the deployment time interval based on collision severity.

A resistance of 0 ohms indicates a short circuit fault in the airbag igniter circuit (short between wires or short to ground), not an open circuit.

This fault causes the SRS system to enter degraded mode: the system disables this specific airbag circuit to prevent accidental deployment and illuminates the airbag warning light.

In a frontal collision, the passenger side may lose second-stage cushioning protection, deploying only the first-stage airbag or failing to deploy entirely, which significantly reduces occupant protection.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin EV Passenger Airbag Short Circuit After Wading

✓
A 2019 BYD Qin EV presented with a constant airbag warning light after driving through deep floodwater. Scanned DTC B178A1A. Removed the interior trim and found the passenger-side floor wiring harness connector CJ103 had accumulated condensation due to a blocked air conditioning drain tube, causing internal pin oxidation and shorting. Cleaned the connector and applied conductive adhesive, replaced the wiring harness seal, and cleared the fault. Also check the air conditioning drain tube for blockages.
BYD DTC AI Analysis

BYD E2 short circuit from pinched wiring harness after accident repair

✓
2020 E2 set DTC B178A1A after front collision repair. Inspection found the instrument panel crossmember mounting bolts installed during the accident repair were too long, penetrating the passenger side second-stage airbag harness corrugated tubing and causing the wire cores to short to body. Replaced the damaged harness section (Part No.: BYD-BCM-SRS-05) and adjusted the bolt length. Fault resolved. Note: Accident repairs must strictly follow repair manual torque specifications.
BYD DTC AI Analysis

BYD E3 airbag module internal igniter aging

✓
An E3 with 80,000 km exhibited intermittent B178A1A faults in humid conditions. With the harness disconnected, the airbag module resistance read normal at ambient temperature but dropped sharply to 0.5 Ω when heated to 60°C. Diagnosed as thermal breakdown of the aged internal igniter insulation. Replaced the passenger airbag assembly and dashboard trim panel (integrated design). Fault resolved.
BYD DTC AI Analysis

Aftermarket passenger-side glove box modification damaged the wiring harness

✓
The owner fitted ambient lighting to the passenger glovebox, drilling holes that damaged the second-stage airbag wiring harness. DTC B178A1A appeared intermittently. Inspection revealed the drill bit had scratched the wiring behind the glovebox, exposing the copper core which contacted the metal dashboard bracket. Cut out the damaged section, soldered in an extension wire, and insulated with double-layer heat shrink tubing to repair the harness. Restored the wiring to its original routing position. Fault cleared. Recommend prohibiting non-professional modifications involving SRS circuits.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.