NO
AU
B2A2C14

DTC B2A2C14 indicates a drive circuit fault in the front passenger side temperature blend door actuator (hot/cold motor), specifically a short to ground (abnormal connection to vehicle ground causing overcurrent) or an open circuit (circuit interruption, infinite resistance) — Seal 6 EV

Thermal Management System

DTC B2A2C14 indicates a drive circuit fault in the front passenger side temperature blend door actuator (hot/cold motor), specifically a short to ground (abnormal connection to vehicle ground causing overcurrent) or an open circuit (circuit interruption, infinite resistance).

The integrated Body Control Module (BCM) controls this motor via a PWM signal or stepper drive to adjust the front passenger side hot/cold air mixing ratio, enabling dual-zone climate control.

The BCM sets this DTC upon detecting abnormal motor drive current (excessive or zero), an abnormal position feedback signal, or a LIN communication fault.

This fault prevents front passenger side temperature adjustment (sticking in the cold or hot position).

In severe cases, the BCM may enter protection mode, limiting overall air conditioning system functionality and potentially affecting the thermal management system's control of battery or motor temperatures.

3
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Deformed fuse holder pin caused loose connection to passenger side temperature control motor

✓
2018 Qin PRO DM. The customer reported the air conditioning operated only in face-vent mode with no ability to adjust temperature or airflow modes; the passenger side showed no temperature change. VDS read DTCs B2A2A14 (mode motor short to ground), B2A2C14 (passenger temperature control motor short to ground), and B2A2C92 (temperature control motor position not reached). Initial inspection revealed an aftermarket GPS unit tapping power from AC fuse IF03. After removing the added harness and replacing the fuse, the fault remained. Further measurement showed unstable supply voltage to the temperature control motor. Investigation found the fuse holder pins had spread from the use of a wider fuse blade during the GPS installation, causing poor contact. Technicians adjusted the fuse holder pin gap to restore clamping force, eliminating the fault.
Original source ↗
BYD DTC AI Analysis

Wiring harness chafed against steering column causing short to earth.

✓
A 2019 BYD Song MAX came in with an intermittent fault: the passenger-side AC temperature would not adjust while driving, working normally at times and failing completely at others. DTC B2A2C14 stored. The fault appeared intermittently during inspection. Removed the glove box and checked the passenger-side temperature blend motor. The connector had no backed-out pins, but measured abnormal voltage drop on the supply. Traced the wiring and found a retaining clip near the evaporator housing had detached, allowing the harness to chafe against the steering column over time. This wore through the insulation on the passenger-side temperature motor supply wire, causing an intermittent short to ground. Repaired the damaged wiring, re-insulated the harness, and secured the routing to prevent further interference. Fault resolved.
Original source ↗
BYD DTC AI Analysis

Stuck air flap mechanism damaged the motor gear and set a short circuit fault.

✓
A 2017 Qin EV300 developed inoperative passenger-side vent temperature adjustment with the AC on, accompanied by distinct clicking. VDS showed DTCs B2A2C14 and B2A2C92 (temperature blend motor unable to reach position). Removing the passenger-side heater box revealed the temperature blend motor gear mechanism severely worn and seized. Manual actuation of the blend door linkage showed extreme resistance, with corrosion on the door shaft. Mechanical binding of the blend door caused continuous motor stall, excessive current draw triggering the short-to-ground protection (B2A2C14), while gear slippage created the clicking noise. Cleaned and lubricated the blend door linkage, replaced the passenger-side temperature blend motor assembly, and performed blend door position calibration. Temperature regulation returned to normal.
Original source ↗
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.