NO
AU
C1200

DTC C1200 indicates the ABS control unit (ECU) detects an electrical integrity fault in the left front wheel speed sensor (WSS) circuit, specifically a short to ground, short to power, or open circuit in the signal line — Seal 6 EV

Braking System

DTC C1200 indicates the ABS control unit (ECU) detects an electrical integrity fault in the left front wheel speed sensor (WSS) circuit, specifically a short to ground, short to power, or open circuit in the signal line.

This sensor is typically a two-wire magnetic or Hall effect type.

During normal operation, it transmits either an AC voltage signal proportional to wheel speed (magnetic type, amplitude varying from 0.1V-3V depending on speed) or a square-wave digital signal (Hall effect type) to the ABS ECU.

The ECU triggers this code when it detects sensor resistance outside the calibrated range (typically 1.0-1.6kΩ), abnormal signal line voltage (continuous 0V or 12V/B+ voltage), or signal interruption time exceeding the threshold.

This fault causes the Anti-lock Braking System (ABS), Electronic Brakeforce Distribution (EBD), Electronic Stability Program (ESP), Traction Control System (TCS), and Autonomous Emergency Braking (AEB) functions to fail or enter a degraded mode.

The fault illuminates the ABS, ESP, and tire pressure/brake system warning lights on the instrument cluster, severely compromising vehicle active safety.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Surui: Internal open circuit in left front wheel speed sensor wiring

✓
**Model:** 2015 BYD Surui 1.5TI **Symptoms:** ABS and ESP warning lights suddenly illuminated while driving. Instrument cluster displayed "Check Brake System." Scan tool read fault code C1200. **Investigation:** Checked sensor connector — no abnormalities. Measured sensor resistance: 1.2kΩ (normal). Checked wiring between sensor connector and ABS ECU. Found the signal wire (white/black) had broken internally at the bend inside the fender liner; only the insulation was intact, causing an intermittent open circuit. **Repair:** Repaired the harness, wrapped it with waterproof heat-shrink tubing, and rerouted it to prevent chafing against the body. Fault cleared.
BYD DTC AI Analysis

BYD Qin Pro DM C1200 Fault After Water Ingress

✓
Model: 2018 Qin Pro DM. Symptom: Multiple dash warning lights came on after driving through standing water in heavy rain. Read DTC C1200 (Left Front Wheel Speed Sensor). Diagnosis: Water inside the left front wheel speed sensor connector. Terminals had green copper corrosion, causing the signal wire to short to ground. Measured resistance to ground at only tens of ohms. Repair: Cleaned the connector pins thoroughly with electronic contact cleaner, dried them with compressed air, applied conductive anti-corrosion grease, and replaced the waterproof seal. Fault cleared. Check underbody sealing.
BYD DTC AI Analysis

BYD Yuan EV: Excessive sensor installation gap causes signal loss

✓
Model: 2019 Yuan EV535. Issue: ABS warning light comes on intermittently on rough roads; normal on smooth roads. Intermittent DTC C1200. Diagnostics: With vehicle stationary, tested sensor resistance and wiring continuity—both normal. Data stream showed left front wheel speed signal intermittently dropping to 0 km/h. On the lift, found left front wheel speed sensor mounting bolt loose; sensor had shifted rearward. Measured air gap between sensor and tone ring at 2.5 mm (spec 0.3–1.2 mm), causing signal interruption on bumps. Fix: Reinstalled sensor, adjusted air gap to 0.8 mm, and tightened bolt to 10 N·m. Road test confirmed fault cleared.
BYD DTC AI Analysis

BYD Song Plus ABS control unit connector oxidized

✓
Model: 2020 Song Plus (petrol). Symptom: C1200 fault code appeared after replacing the left front steering knuckle; would not clear. Repair process: Checked the replacement sensor and harness—no faults found. Sensor resistance: 1.1kΩ (normal). Wiring continuity: good. Suspected ABS ECU. Found oxidation/greening on the left front wheel speed signal input pin (pin 12) of the ECU connector, with contact resistance at 5.8Ω. Resolution: Cleaned the ECU connector pins with precision electrical contact cleaner, adjusted pin opening with special tools for proper contact pressure, and applied electrical contact protectant. Fault cleared.
BYD DTC AI Analysis

BYD e2 wheel speed sensor internal short circuit

✓
Model: 2020 BYD e2 (electric). Symptoms: Vehicle failed to enter READY mode. Dashboard displayed "Braking System Fault". DTC C1200 present. Repair: Measured left front wheel speed sensor resistance at only 120Ω (well below the 1.2kΩ specification), indicating an internal coil inter-turn short. Harness-side supply voltage was 12V – normal. Signal wire to ground read 0V (should be ~2.5V bias voltage). Replaced the left front wheel speed sensor. Cleared the DTC, but it returned after several kilometres. Found the replacement was an aftermarket sensor with out-of-spec resistance. Installed a genuine sensor; fault eliminated.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.