NO
AU
B175B-00

DTC B175B-00 indicates the SRS (Supplemental Restraint System) control unit detects the right rear side airbag igniter circuit resistance (typically located in the right rear seat side or C-pillar trim panel) falls below the manufacturer threshold (normal range: 1 — Seal U

Safety System

DTC B175B-00 indicates the SRS (Supplemental Restraint System) control unit detects the right rear side airbag igniter circuit resistance (typically located in the right rear seat side or C-pillar trim panel) falls below the manufacturer threshold (normal range: 1.8–3.0 Ω; fault condition: below 1.0 Ω or near 0 Ω).

This constitutes a low-resistance airbag circuit fault, meaning the control unit identifies a short circuit risk (wiring harness short to ground, wire-to-wire short, or internal short within the airbag module).

Consequently, the affected side airbag may fail to deploy during a collision (as the ECU interrupts the trigger signal due to the circuit anomaly) or, in extreme cases, deploy unintentionally.

Simultaneously, the SRS system illuminates the instrument cluster airbag warning light and may disable the entire airbag system to protect occupants.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Right rear seat adjuster chafed through wiring harness, causing short circuit

✓
2017 BYD Qin EV300, 80,000 km. Airbag warning light on; DTC B175B-00. Inspection found the right rear seat rail wiring harness rubbing against the seat adjustment mechanism's metal edge. Long-term friction wore through the insulation, exposing two bare wires that contacted and shorted. Repair: Wrapped the damaged section with insulation tape, rerouted the harness, added corrugated tubing, and secured with cable ties to prevent interference with moving parts. Fault cleared.
BYD DTC AI Analysis

C-pillar connector corroded after water wading, causing low resistance

✓
Qin EV450 airbag warning light triggered after wading through heavy rain. Scan tool showed right rear side airbag resistance at 0.8Ω (low). Removed lower right C-pillar airbag connector and found water staining and green copper corrosion inside. Cause: Sunroof drain hose connector deteriorated and detached, letting rainwater run down the A-pillar, across the floor and into the C-pillar. Repair: Cleaned connector pins with electrical contact cleaner, applied conductive protective grease, repaired the drain hose. Cleared fault codes; no recurrence.
BYD DTC AI Analysis

Loose connector after accident repair causes intermittent fault

✓
After repairing a right rear side collision on a Qin 100, the dashboard intermittently displayed an airbag fault. Testing revealed intermittent DTC B175B-00. Inspection found technicians had replaced the right rear side airbag during the accident repair, but the connector locking tab had not fully engaged. Vehicle vibration caused poor terminal contact, with resistance fluctuating between 0.5 and 2.0 Ω. After reseating the connector and confirming the locking tab clicked into place, the data stream showed stable resistance at 2.2 Ω and the fault resolved.
BYD DTC AI Analysis

Airbag module requires replacement due to internal igniter short circuit

✓
A 2018 Qin EV300 showed persistent DTC B175B-00. Disconnected the airbag module and connected a simulator to the harness; the DTC changed to open circuit (normal). Harness insulation to ground measured good. Measured the airbag module resistance separately: 0.2Ω, well below the 2.0Ω standard. Determined the airbag igniter was internally shorted. Replaced the right rear side airbag module (required new mounting bracket and bolts), performed system configuration write, and cleared the fault.
BYD DTC AI Analysis

Aftermarket seat heating pad installation pinched wiring harness

✓
A Qin 80 owner reported an illuminated airbag warning light after installing an aftermarket seat heater. Inspection found that while drilling into the right rear seat foam to route wiring, the installer used screws that were too long, piercing the harness sheath and shorting the airbag harness positive and negative leads. Replaced the damaged harness section (severe internal damage required replacing the entire section). Rerouted the wiring to avoid the heating elements. Fault resolved.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.