NO
AU
B176E-00

DTC B176E-00 is an SRS (Supplemental Restraint System) fault code indicating a short to body ground (GND) in the left rear seat belt pretensioner drive circuit — Seal U

Safety System

DTC B176E-00 is an SRS (Supplemental Restraint System) fault code indicating a short to body ground (GND) in the left rear seat belt pretensioner drive circuit.

The pretensioner is a pyrotechnic actuator containing an igniter and gas generant.

During a collision, the SRS ECU triggers the pretensioner.

The resulting explosive force rapidly tightens the seat belt, removing slack between the occupant and the belt.

This fault code indicates a short to ground (resistance below the threshold, typically <2Ω) in the wiring harness between the SRS ECU and the left rear pretensioner, or within the pretensioner itself.

This causes the ECU to detect an abnormal current path.

Upon detecting this fault, the SRS system illuminates the airbag warning lamp and enters fail-safe mode.

This disables the left rear pretensioner and any linked side airbag functions, severely compromising crash safety performance.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Water ingress in left rear carpet of water-wading vehicle caused pretensioner short circuit.

✓
A 2017 Qin EV300 came in with the airbag warning light on after driving in heavy rain. DTC B176E-00 stored. The left rear sunroof drain hose had detached, allowing water to accumulate under the left rear carpet. The pretensioner harness connector under the seat showed severely oxidized pins with green copper corrosion. Resistance from the pretensioner side plug to ground measured only 0.8Ω. Replaced the sunroof drain hose, cleaned and dried the connector with electronic cleaner and a heat gun, applied conductive protectant, and reinstalled it. Fault resolved.
BYD DTC AI Analysis

Aftermarket seat modification pinched wiring harness, causing short circuit

✓
A 2018 Qin EV450 owner self-installed a left rear seat heating pad. When reinstalling the seat after disassembly, the owner failed to route the pretensioner wiring harness (yellow) into its designated slot, leaving it pinched by the seat slide rail mounting bolt. Over time, the bolt head wore through the insulation, exposing the conductor to the seat frame (ground). During diagnosis, the fault code appeared intermittently whenever the left rear seat moved. Repaired by cutting out the damaged harness section, soldering in an extension wire, and rerouting and securing the harness to its retaining clips per the standard layout. Fault cleared.
BYD DTC AI Analysis

Pretensioner connector not fully seated after accident repair

✓
A 2017 Qin 100 sustained left rear damage in a scrape; an independent workshop replaced the left rear door and B-pillar trim. One month post-repair, DTC B176E-00 set. Inspection found the pretensioner connector (below the B-pillar) was not fully locked, the waterproof seal had shifted, and internal metal terminals were tilted, with one terminal touching the connector housing (ground). Replaced the pretensioner harness connector (terminals deformed beyond repair), ensured the connector clip fully engaged, and wrapped the joint with waterproof tape. Fault resolved.
BYD DTC AI Analysis

Pretensioner internal igniter insulation breakdown

✓
A 2017 Qin 80 with no accident history. The SRS warning light suddenly illuminated while driving, logging DTC B176E-00. Checked the wiring harness—no damage or water ingress; harness-to-ground insulation measured normal. Disconnected the pretensioner connector and measured resistance from both pins to the metal housing; one pin showed continuity to ground (0.3Ω). This indicated the pretensioner internal igniter insulation had broken down. Replaced the left rear seatbelt assembly (pretensioner integrated with seatbelt, not available separately), wrote the SRS system configuration, and cleared the fault.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.