NO
AU
B2A0E12

This DTC indicates a short to battery in the signal circuit of the Battery Thermal Management System (BTMS) inlet coolant temperature sensor (typically located on the line before the battery cooling circuit enters the battery pack) — Seal U

Thermal Management System

This DTC indicates a short to battery in the signal circuit of the Battery Thermal Management System (BTMS) inlet coolant temperature sensor (typically located on the line before the battery cooling circuit enters the battery pack).

The sensor utilizes an NTC (Negative Temperature Coefficient) thermistor and outputs a 0-5V analog voltage signal to the BMS or thermal management controller during normal operation.

During a short to battery (12V), the ECU detects a continuous signal voltage above the normal range (e.g., >4.8V or equal to battery voltage) and registers a short circuit fault.

This fault prevents the BMS from accurately reading the battery pack inlet coolant temperature, affecting the battery thermal management strategy and potentially triggering: 1) Disabled battery fast charging or limited discharge power; 2) False battery over-temperature protection triggers, forcing the battery cooling system (electric compressor, water pump) to operate; 3) Thermal runaway risk in extreme cases due to the inability to monitor actual battery temperature.

This is a severe DTC.

Inspect and repair immediately due to the high-voltage battery system thermal runaway risk.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

2019 Qin EV sets DTC B2A0E12 and cannot fast charge after driving through water.

✓
After driving through flood water, the instrument cluster displayed "Check Powertrain" and fast charging failed. VDS retrieved DTC B2A0E12 (battery pack inlet water temperature sensor short circuit) along with multiple network faults. Inspection found water inside the battery pack front inlet water temperature sensor connector; severe green corrosion had shorted the signal terminal to the 12V reference supply. Repair: Cleaned the connector terminals with anhydrous alcohol, dried them, applied conductive paste, and repaired the sealing ring. The sensor internals were damaged, so the inlet water temperature sensor was replaced. After clearing the fault codes, the data stream showed inlet temperature back to normal at 28°C and fast charging restored.
BYD DTC AI Analysis

Wiring harness worn through and shorted after Qin EV underbody scrape

✓
The vehicle bottomed out while driving. No issues appeared initially, but DTC B2A0E12 triggered the following day accompanied by a "Battery temperature too high" warning. Raised on a lift, found the edge of an underbody shield mounting bracket had cut through the coolant temperature sensor wiring harness at the battery pack inlet. The signal wire (pink) contacted the reverse light power wire (red) at the damaged section, causing a short circuit. Stripped back the insulation, resoldered the signal wire, and applied double-layer heat shrink tubing. Rerouted the harness away from sharp edges and added corrugated tubing protection. Verified no short circuit remained, cleared the DTC, and road tested. Fault resolved.
BYD DTC AI Analysis

Internal short in Qin EV coolant temperature sensor causing false reading

✓
The vehicle suddenly set DTC B2A0E12 during normal operation, with the dashboard displaying a Thermal Management System Fault. Connected a scan tool and checked live data: Battery Pack Inlet Temp read -40°C or showed an abnormal 12V value (matching battery voltage). Disconnected the sensor connector and measured 0V on the harness side signal wire (normal), but 0.5Ω across the sensor terminals (near short). Diagnosed as internal thermistor breakdown. Replaced the battery pack inlet coolant temperature sensor (use OEM parts with matching resistance curves), refilled coolant and bled the system, cleared the fault codes. Live data then showed normal temperature readings varying with ambient temperature. Fault resolved.
BYD DTC AI Analysis

Qin EV aftermarket underbody shield crushed wiring harness, causing short circuit

✓
One week after the owner installed an aftermarket underbody guard, a B2A0E12 code appeared. Inspection found the mounting bolts were too long and pierced the protective sheath of the battery pack inlet coolant temperature sensor harness, shorting the signal wire to the bolt. The bolt connects to chassis ground, but at this location it was compressed against the reversing light power supply wiring. Fix: Removed the aftermarket guard. Repaired the harness by cutting out the damaged section and re-crimping the terminals. Replaced the bolts with OEM standard-length fasteners. Rerouted the harness to maintain at least 20 mm clearance from sharp metal edges and power cables. Replaced the damaged sensor. Fault resolved.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.