UAE
AU
B16201B

B16201B is a BYD SRS (Supplemental Restraint System) diagnostic code indicating a communication interruption or open electrical connection between the driver's seat side airbag and the SRS control unit — Atto 3

Safety System

B16201B is a BYD SRS (Supplemental Restraint System) diagnostic code indicating a communication interruption or open electrical connection between the driver's seat side airbag and the SRS control unit.

This DTC sets when the SRS ECU detects the driver's side airbag circuit resistance exceeds the standard range (typically 2.0-3.0Ω ±0.5Ω), indicating an open circuit or high resistance.

This incomplete airbag deployment circuit prevents the system from igniting the gas generator during a side impact.

This fault forces the SRS into a degraded mode.

The driver's seat side airbag becomes inoperative, but other airbags (front, curtain) typically remain functional.

Despite involving the high-voltage interlock and safety systems, the vehicle remains drivable with reduced occupant protection.

This fault continuously illuminates the instrument cluster airbag warning light on some models.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Loose connector under E2 seat triggered intermittent warning

✓
Vehicle: 2019 BYD E2, 32,000 km. Symptoms: The airbag warning light on the instrument panel illuminates intermittently, especially on rough roads. DTC B16201B appears sporadically. Diagnosis: The yellow 2-pin connector under the driver's seat was not fully locked; the retaining clip showed wear. Cause: Frequent seat adjustment pulled the wiring harness during seat movement, loosening the connector. Fix: Re-seated and locked the connector, secured the harness routing with cable ties to avoid interference with the seat rails, cleared the fault code, and monitored for one week. No recurrence.
BYD DTC AI Analysis

Internal open circuit in Qin EV seat airbag module

✓
Vehicle: 2019 Qin EV, post-accident repair. Symptoms: Airbag warning light stays on after repairs. VDS shows current fault code B16201B. Diagnosis: Harness side resistance normal at 2.4 Ω; airbag module side resistance infinite. Disassembled seat and found corroded internal pins on side airbag gas generator connector (water entered during accident, not fully dried). Solution: Replaced driver side airbag module (part no. EPB-5820100), coded and matched new module, cleared fault codes after bus communication test passed.
BYD DTC AI Analysis

E3 seat rail wiring harness worn through, open circuit

✓
Vehicle: 2020 BYD E3, ride-share, 85,000 km. Symptoms: Airbag light always on, DTC B16201B. Fault code status changes when adjusting the seat. Diagnosis: Peeled back the harness protective sleeve under the seat. Found two wires nearly worn through at the seat rail corner, held by only a few copper strands. Cause: Long-term frequent seat adjustment caused the harness retaining clip to detach, letting the harness rub against the metal rail. Solution: Soldered and heat-shrink repaired the wires, rerouted the harness path, added anti-chafe sleeving, and adjusted harness length slack.
BYD DTC AI Analysis

SRS ECU software false alarm upgrade case

✓
Vehicle: 2019 Qin EV, driven in cold climates. Symptoms: DTC B16201B appeared intermittently during cold morning starts, self-cleared as temperature rose; wiring harness readings normal. Diagnosis: Comparison with same-period models confirmed early ECU software (V1.2) set resistance detection thresholds too strict for low temperatures. Resolution: Upgraded SRS control unit software online to V1.5 via VDS. The new software optimizes the resistance compensation algorithm for low-temperature conditions. DTC has not returned since the upgrade.
BYD DTC AI Analysis

Seat modification damaged the wiring harness connector.

✓
Vehicle: 2020 E3, after installing sport seats. Symptoms: Airbag light came on immediately after the modification, setting DTC B16201B. Diagnosis: Inspection found the shop cut the original harness to connect the new seats directly instead of using the OEM SRS adapter. This caused poor terminal contact and reverse polarity risk. Solution: Restored the original vehicle harness (ordered a new harness assembly), used the OEM-specified seat adapter harness, and matched airbag circuit impedance. Cleared fault codes and the system returned to normal.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.