UAE
AU
B16A1

DTC B16A1 indicates the airbag control unit (SRS ECU) detects an internal fault or abnormal communication with connected left-side safety system components — Atto 3

Safety System

DTC B16A1 indicates the airbag control unit (SRS ECU) detects an internal fault or abnormal communication with connected left-side safety system components.

Specific causes include an SRS ECU internal processor error, memory fault, software anomaly, or a communication interruption with the left side impact sensor (left B-pillar), left seat belt pretensioner, or left seat occupancy detection sensor.

This critical airbag system fault indicates the ECU may fail to receive left-side impact signals or execute airbag deployment commands.

Consequently, the left side airbag, side curtain airbag, or seat belt pretensioner may fail to deploy during a side impact.

This severely degrades vehicle passive safety protection and requires immediate repair.

3
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Han EV B16A1 Fault (Left B-Pillar Sensor Communication Error)

✓
Symptoms: Dashboard intermittently displayed safety system warning light. Diagnostic tool read DTC B16A1 (left B-pillar area sensor communication fault). Diagnosis: Inspected the left B-pillar lower wiring harness and found the retaining clip was loose. The harness had chafed against the body metal edge, damaging the CAN-H wire insulation and causing a short to ground. Signal voltage was only 1.2V. Fix: Repaired the damaged CAN-H wire and insulated it with heat shrink tubing. Re-secured the harness routing and added anti-chafe sleeving. Cleared the fault codes and performed the sensor calibration procedure. Fault resolved.
Original source ↗
BYD DTC AI Analysis

BYD Song Plus DM-i B16A1 Fault (Left Door Safety System LIN Communication)

✓
Symptoms: Intermittent failure of driver's side window operation, delayed response from door lock actuators, and intermittent failure of left front door control functions. Diagnosis: Connected a diagnostic scan tool and confirmed DTC B16A1 is related to communication timeout with the left front door control module (DCM). Measured the wiring harness connector below the left A-pillar and found abnormal LIN bus voltage (pulled down to 0.8V). Disassembly revealed the wiring harness at the door hinge had suffered long-term flexing damage, causing the insulation on both the LIN wire and ground wire to break and short together. Repair: Separated the shorted LIN and ground wires and insulated each individually. Added protective corrugated tubing to the wiring harness at the door hinge. Replaced the left front door control module and recalibrated the window anti-pinch function.
Original source ↗
BYD DTC AI Analysis

BYD Tang DM B16A1 fault (left seat belt pretensioner communication fault)

✓
Symptoms: SRS warning light stayed on after accident repairs. Diagnosis: Scanned SRS system; DTC B16A1 indicated left seat belt retractor sensor. Checked the seat belt assembly inside the left B-pillar trim and found the aftermarket unit installed during the accident repair had an incorrect connector type. Measured sensor resistance—it deviated significantly from standard values (2.4–3.6 Ω). Compared left and right data streams; the left side showed no signal feedback. Repair: Replaced the aftermarket seat belt assembly with a genuine left side unit (with pretensioner and sensor). Reprogrammed and calibrated the airbag system. Cleared fault codes, ran impact sensor self-test; the warning light went out.
Original source ↗
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.