UAE
AU
C050400

DTC C050400 indicates the IPB (Intelligent Integrated Braking System) control unit detects an "indirect uncertainty" (plausibility fault) in the left front wheel speed sensor signal — Atto 3

Braking System

DTC C050400 indicates the IPB (Intelligent Integrated Braking System) control unit detects an "indirect uncertainty" (plausibility fault) in the left front wheel speed sensor signal.

This is not a simple sensor open or short circuit.

Instead, the control unit algorithm identifies a logical inconsistency between the left front wheel speed signal and the vehicle's actual motion state, the speeds of the other three wheels, and the longitudinal/lateral acceleration sensor data.

Symptoms include signal spikes, an abnormal fixed value (such as a constant 1845 km/h), a signal rate of change exceeding physical limits, or intermittent signal loss within specific vehicle speed ranges (usually >60 km/h).

This fault triggers degraded protection modes in systems including ABS, ESP, and automatic emergency braking, severely affecting vehicle dynamic stability control.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Song PLUS DM-i ABS light on during high-speed driving; wheel speed signal stuck at 1845km/h

✓
Symptoms: Engine and ABS warning lights illuminated intermittently while driving, readily reproduced above 60 km/h. Once triggered, the left front wheel speed signal froze at 1845km/h. Diagnosis: Scan tool retrieved P121B00 (Left Front Wheel Speed Sensor Signal Abnormal) from CEMS and C050400 (Left Front Wheel Speed Sensor Signal Fault) from IPB. Disconnected the sensor connector and inspected the ABS plug pins; no abnormalities. Replaced the sensor but the fault persisted. Removed the driveshaft and found the magnetic encoder ring coated in iron filings. Solution: Cleaned the iron filings from the encoder ring, reinstalled the driveshaft, and test drove. Fault eliminated. Key point: You cannot see the internal debris by removing only the wheel speed sensor; you must remove the driveshaft to clean it thoroughly.
Original source ↗
BYD DTC AI Analysis

BYD All-Model Wheel Speed Sensor General Diagnostic Procedure (Official Technical Bulletin)

✓
Symptoms: Dashboard ABS/ESP warning lights on, ESP function limited, possible abnormal ABS activation while driving. Diagnostic procedure: 1. Used VDS to read ESP/ABS DTCs, confirmed C050400. 2. Checked left front wheel speed sensor harness connections and resistance (normal: 1.0–1.5 kΩ). 3. Checked installation gap (0.2–1.2 mm). 4. Inspected reluctor ring for metal debris, oil, or damage. 5. Used oscilloscope to check wheel speed sensor signal for interruptions or abnormalities. Resolution: Clean or replace left front wheel speed sensor; clean or replace half-shaft magnetic encoder ring; repair wiring harness short/open; replace half-shaft assembly if necessary.
BYD DTC AI Analysis

Song/Qin Series Multi-System Warning (ESP/ABS Fault)

✓
Symptoms: While driving, the instrument panel suddenly displayed "Check ESP System" and "Check ABS System" warnings, accompanied by multiple system alerts. Diagnosis: Scanned the vehicle using VDS1000 and retrieved C050400 (Left Front Wheel Speed Sensor Signal Fault) from the ESP module. Found slight oxidation on the wheel speed sensor connector. Resistance measured within normal range but voltage signal was unstable. Further inspection revealed abnormal wear marks between the sensor and the tone ring. Resolution: Replaced the left front wheel speed sensor, cleaned the connector and applied conductive grease, and removed oxides from the tone ring surface. Cleared the fault codes and road tested 20 km. Fault did not reappear.
Original source ↗
BYD DTC AI Analysis

Intermittent brake system fault in new energy vehicles (intermittent short circuit in wiring harness)

✓
Symptoms: BYD Tang/Han models intermittently display "Check Brake System" on the instrument cluster while driving, with ESP function restricted and abnormal vehicle speed signals. Diagnosis: Scanned the ABS/ESP system and retrieved DTC C050400. Data comparison revealed intermittent fluctuations in the left front wheel speed signal. Raised the vehicle and found the left front wheel speed sensor harness rubbing against the fender liner at full steering lock; worn insulation caused an intermittent short to ground. Inspection also found metal powder from brake pad wear covering the target wheel surface. Repair: Repaired the damaged harness and rerouted it to avoid interference. Thoroughly cleaned the left front half-shaft magnetic encoder target wheel (removed the half-shaft for cleaning). Replaced the damaged harness protective sleeve.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.