UAE
AU
C050A00

DTC C050A00 indicates the IPB (Intelligent Integrated Braking System) ECU detects the air gap between the right front wheel speed sensor (WSS) and the signal tone ring exceeds the calibrated tolerance range (typically 0 — Atto 3

Braking System

DTC C050A00 indicates the IPB (Intelligent Integrated Braking System) ECU detects the air gap between the right front wheel speed sensor (WSS) and the signal tone ring exceeds the calibrated tolerance range (typically 0.3-1.2mm), or the sensor signal amplitude/phase exhibits intermittent erratic characteristics.

This is a plausibility fault, distinct from a direct short or open circuit.

The IPB system uses an active Hall-effect wheel speed sensor highly sensitive to the installation air gap.

An excessive gap attenuates the signal, while an insufficient gap causes the sensor head to rub against the tone ring.

The ECU sets this fault when algorithmic compensation cannot verify wheel speed signal reliability.

This fault degrades or disables ABS, ESP, TCS, and Automatic Emergency Braking (AEB) functions.

In severe cases, it illuminates the brake system warning lamp continuously.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Dolphin ESP false trigger: Bearing wear increased air gap

✓
Symptoms: The BYD Dolphin’s ESP warning light illuminated intermittently while driving, with a kick-back sensation through the brake pedal. Scan tool retrieved DTC C050A00 (Right Front Wheel Speed Sensor Air Gap Abnormal). Diagnosis: Raised the vehicle and inspected the right front wheel speed sensor; it appeared undamaged. Measured the sensor air gap and found a maximum of 1.8 mm (exceeding specification). The wheel bearing also showed noticeable axial play—0.5 mm of vertical movement when pushing the tire up and down. The worn hub bearing caused the integrated ABS tone ring to sink, creating an uneven air gap. Repair: Replaced the right front wheel hub bearing assembly (including the ABS tone ring). Reinstalled the OEM sensor and adjusted the air gap to 0.6 mm. Cleared the fault codes and road-tested; ESP function returned to normal.
BYD DTC AI Analysis

Signal plate deformed after Yuan Plus bottomed out

✓
Symptoms: Right front wheel struck a curb. Dashboard displayed 'Braking System Fault'. DTCs C050A00 and C003400 retrieved (right front wheel speed sensor signal fault). Diagnosis: Removed right front wheel. Found slight scrape marks on the wheel speed sensor head and localized denting on the tone ring (magnetic ring), causing periodic air gap variation during rotation. Resolution: Replaced right front wheel speed sensor and wheel hub bearing unit together (tone ring is integrated with the bearing). Set air gap to workshop manual specifications during installation. Fault resolved.
BYD DTC AI Analysis

BYD Seal intermittent fault: Silt in mounting hole causing abnormal air gap

✓
Symptoms: After driving through water, the BYD Seal's ESP warning light flashed intermittently. The scanner logged intermittent DTC C050A00. Diagnosis: Checked the sensor connector for water ingress; none found. Measured sensor resistance; normal. Removed the sensor and found heavy sediment buildup in the mounting bore preventing full seating, resulting in an air gap exceeding specification. After cleaning and reinstalling, the air gap remained slightly over the upper limit at 1.3mm. Resolution: Thoroughly cleaned the mounting seat. Installed a new sensor with adjustment shim. Used a feeler gauge to check multiple points and verified air gap within 0.3-1.2mm. Cleared the DTC; the fault has not recurred.
BYD DTC AI Analysis

Qin PLUS DM-i Aftermarket Bearing Dimensional Deviation

✓
Symptoms: Following replacement of the right front wheel hub bearing at an independent workshop, the BYD Qin PLUS DM-i showed constant ABS/ESP warning lights and set DTC C050A00. Diagnosis: Comparing the old and new bearings revealed the aftermarket unit's magnetic encoder ring position deviated approximately 0.5 mm axially from the OEM part. This left the sensor air gap too small after installation (measured at 0.2 mm), saturating the sensor signal. Solution: Installed an OEM wheel hub bearing assembly, adjusted the air gap to specification, calibrated the wheel speed sensor with a diagnostic tool, and cleared the fault.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.