UAE
AU
B121B09

This fault code indicates a functional failure of the No — Atto 8

Thermal Management System

This fault code indicates a functional failure of the No. 2 IGBT (Insulated Gate Bipolar Transistor) driver chip in the thermal management system PTC (Positive Temperature Coefficient) heater controller.

In BYD Qin series vehicles, the PTC heater uses IGBTs for PWM power modulation to control heating output. "2#" usually refers to the second drive circuit in a dual-channel PTC control system or the driver IC for the second unit of the IGBT module.

Fundamentally, the driver IC fails to generate a normal gate drive signal, preventing the IGBT from switching on and off correctly.

This directly disables the PTC heater, resulting in no warm air from the air conditioning and battery heating function failure.

Extreme cases may cause an IGBT shoot-through short circuit, creating a high-voltage safety risk.

Underlying faults such as overtemperature, overcurrent, or power supply abnormalities typically accompany driver chip failures.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Qin Pro DM PTC controller cooling failure caused IGBT driver chip burnout.

✓
A 2019 Qin Pro DM with 60,000 km displayed 'Thermal Management System Fault' on the dash and had no heat from the heater. Retrieved fault codes B121B09 and B121C09 (No. 2 and No. 3 IGBT driver failure). Found the PTC controller cooling circuit heavily blocked with scale, causing poor IGBT module cooling. The module temperature sensor read 145°C (normal <80°C). Disassembling the PTC controller revealed the No. 2 IGBT driver IC (IR2184) had a burned and carbonized surface. Replacing the PTC controller assembly, flushing the cooling system lines, and changing the coolant resolved the fault. Root cause: The coolant had not been changed for a long time, allowing corrosive ions to build up, corrode the aluminum radiator, and create blockages.
BYD DTC AI Analysis

BYD Qin EV300 drive power chip failure causing intermittent PTC failure

✓
2017 BYD Qin EV300. The PTC heater worked normally during cold starts, but cabin heating suddenly stopped after 10 minutes of driving. DTC B121B09 appeared intermittently. In the hot state, the 15V drive power supply at the PTC controller measured 8V, dropping from 15V as temperature increased, triggering the drive chip's undervoltage protection. Inspecting the PCB revealed dry solder joints on the 15V voltage regulator (78M15) due to long-term thermal stress. Re-soldering the voltage regulator and adding a thermal pad stabilised the 15V supply at 14.8V and cleared the fault. This case demonstrates the critical impact of drive power supply stability on IGBT drive.
BYD DTC AI Analysis

PTC heater short circuit triggered IGBT driver overcurrent lockout

✓
2018 BYD Qin Pro DM. The owner reported that after turning on the heater, the instrument cluster displayed a thermal management fault and all cabin heat was lost. The scan tool showed active DTC B121B09. Live data indicated the PTC operating current spiked to 35A (rated 15A) and then the fault triggered. Measured insulation resistance between the PTC heater high-voltage positive and negative terminals and the case; the positive-to-case measurement was only 0.8MΩ (standard >20MΩ). Disassembly revealed cracked PTC ceramic elements, which allowed coolant ingress. Replaced the PTC heater core and controller (the IGBT driver chip had sustained overcurrent damage), and repaired the high-voltage wiring harness insulation. This resolved the fault. Note: PTC body insulation failure is a common cause of IGBT driver chip overcurrent damage.
BYD DTC AI Analysis

Software calibration error caused IGBT drive timing fault.

✓
A 2019 Qin PRO DM developed a B121B09 fault code with the PTC inoperative after a 4S dealership upgraded the air conditioning system software. Hardware inspection revealed no damage. Measuring the drive signal showed a dead time of only 0.5μs (normal should be >2μs), creating a risk of shoot-through between the upper and lower bridge arms and triggering protection lockout in the driver chip. Checking the technical bulletin confirmed a calibration defect in software version V2.1 of the PTC controller for this batch of vehicles. Reflashing with version V2.3 software and adjusting the IGBT turn-on/turn-off delay parameters restored normal drive waveforms and cleared the fault code. This case highlights the need to match software versions.
Other Atto 8 Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.