UAE
AU
B169E

B169E (SRS_ECU Fault) indicates the Airbag Control Unit (ACU) detected an internal circuit abnormality, a power supply/ground fault, or a critical communication bus interruption — Atto 8

Safety System

B169E (SRS_ECU Fault) indicates the Airbag Control Unit (ACU) detected an internal circuit abnormality, a power supply/ground fault, or a critical communication bus interruption.

This fault code signifies the SRS ECU cannot execute the self-test procedure, or it detected a functional failure in the internal processor, memory, or ignition loop monitoring circuit.

This is a Hard Fault, meaning the airbag system may be in a complete failure or degraded mode.

In a collision, the airbags or pretensioners may fail to deploy, posing a severe safety hazard.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

2020 BYD Tang DM B169E fault after wading through water

✓
Vehicle flooded to floor level. The next day the instrument cluster displayed 'SRS Fault'. The diagnostic tool read active DTCs B169E (SRS ECU Fault) and B1650 (Front Left Collision Sensor Communication Fault). Dismantling revealed the SRS ECU mounted beneath the floor. The housing seal had deteriorated, allowing water ingress, and the circuit board showed green corrosion. Replaced the ACU module, cleaned the corroded harness connectors, resealed and reinstalled the assembly, then performed coding matching and crash data reset. Fault resolved.
BYD DTC AI Analysis

2019 BYD Yuan EV ACU locked after accident repair

✓
Vehicle had a front-end collision. Airbags did not deploy; front bumper sustained damage. After repairs, fault codes were cleared but B169E would not erase. Analysis indicated the impact sensor generated a hard-coded signal from the shock, causing the ACU to enter a collision warning lock state. Inspection found the left front impact sensor's internal accelerometer damaged, outputting 0.2 V instead of the normal 2.5 V reference. Replaced left front impact sensor and SRS ECU (the ECU had logged the collision event and locked). Performed online coding and sensor zero-point calibration. System returned to normal.
BYD DTC AI Analysis

2021 BYD Qin Pro: Low-voltage battery drain causes abnormal ECU reset

✓
Customer reported the SRS light stayed on after jump‑starting the vehicle following long‑term storage. Diagnosis showed DTCs B169E (internal fault) and U0151 (loss of communication with SRS ECU). Battery voltage measured only 10.8V; the jumper cables had been connected with reversed polarity during the jump‑start. Low voltage and the reverse‑polarity voltage surge caused the SRS ECU internal memory data verification to fail. Replaced the 12V battery. Powered the system with a regulated 14V supply. Using the diagnostic tool, performed the ‘ECU Reset and Data Recovery’ procedure and updated the SRS software to the latest version (Ver 3.2.1). Cleared all fault codes. System self‑test passed.
BYD DTC AI Analysis

CAN bus interference caused by aftermarket modifications to BYD Song MAX

✓
After installation of a 360-degree panoramic camera system, the SRS warning light illuminated intermittently. We retrieved historical fault codes B169E and U1100 (CAN communication error). Inspection found the modification shop had spliced into the wiring to draw power from the OBD port, mistakenly connecting the CAN-H line in parallel with the airbag system’s dedicated CAN bus. This caused signal reflection and interference. We repaired the wiring harness, separated the modification device from the SRS system bus, and fitted ferrite core filters to the CAN lines. After clearing the faults, we monitored the vehicle for one month, and the issue did not recur.
Other Atto 8 Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.