UAE
AU
B176E

DTC B176E indicates the SRS (Supplemental Restraint System) control unit detects an abnormally low-resistance path between the Left Rear Seat Belt Pretensioner drive circuit and the vehicle power supply (+B), indicating a short to power — Atto 8

Safety System

DTC B176E indicates the SRS (Supplemental Restraint System) control unit detects an abnormally low-resistance path between the Left Rear Seat Belt Pretensioner drive circuit and the vehicle power supply (+B), indicating a short to power.

The pretensioner contains a squib controlled by the SRS ECU, with a normal operating resistance of approximately 2.0-3.0 Ω.

If the wiring harness or connector shorts to a 12V power wire, the ECU detects an abnormally high voltage or resistance value, immediately sets this DTC, and enters fail-safe mode.

This fault presents two risks: first, during a collision, circuit protection may prevent the left rear pretensioner from deploying, causing occupant restraint failure; second, the short-circuit current may accidentally trigger the squib, causing the seat belt to retract suddenly and injure the occupant.

Consequently, the SRS system immediately cuts power to this circuit and illuminates the airbag warning lamp, potentially disabling the entire airbag system.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Song MAX: Left rear seat modification pinched wiring harness, causing short circuit

✓
A 2019 BYD Song MAX with 30,000 km had the airbag warning light on steady. Scanning revealed DTC B176E. The owner reported rear seat heating pads installed at a repair shop one week prior. Removing the left rear B-pillar trim revealed the seatbelt pretensioner harness pinched by the seat heater power cable (red 12V constant) through a metal clamp, with the insulation worn through and copper core exposed. Cut out the damaged section, soldered in an extension, and sealed it with heat-shrink tubing. Rerouted the harness to clear the seat rails and isolated the seat heater power cable. Cleared the fault codes and the SRS system returned to normal.
BYD DTC AI Analysis

BYD Yuan EV: Connector corrosion and short circuit after water ingress

✓
2019 Yuan EV airbag warning light came on after driving in heavy rain. Scanner reported B176E. Inspection found water marks on the left rear sill. Removed the left rear seatbelt pretensioner connector (located below the B-pillar) and found green corrosion and water in the terminals. Resistance between the pretensioner drive terminal and the adjacent constant power terminal measured only 0.5Ω, creating a short. Cleaned the connector with electronic cleaner, blow-dried it, applied conductive anti-corrosion grease, and installed a new waterproof connector housing. Also checked the sunroof drain tubes for blockages to prevent further water ingress. Fault resolved.
BYD DTC AI Analysis

Tang DM wiring harness chafing on sharp body edge

✓
2021 Tang DM, 80,000 km. Intermittent airbag warning light with fault code B176E. Shake test found the left rear B-pillar harness contacting a sharp burr on the body panel when the vehicle hit bumps. Peeling back the yellow corrugated tubing revealed a deep scratch in the wire insulation that touched chassis ground or adjacent power wires during vibration. Wrapped the damaged area with insulation tape, fitted a rubber sleeve to isolate the sharp edge, and adjusted the harness mounting point for more slack. Road tested 20 km; fault did not return.
BYD DTC AI Analysis

Qin Pro petrol SRS ECU internal driver fault

✓
2020 Qin petrol variant. After accident repair (left rear quarter panel straightening), replaced the left rear seatbelt assembly, but DTC B176E persisted. Disconnected the pretensioner connector and still measured 12V abnormal voltage on the harness side; the wiring harness was intact with no visible damage. Further disconnected the SRS ECU connector and checked continuity between the pretensioner drive pin and power pin, finding an internal short in the ECU. Root cause: The collision's instantaneous high current damaged the ECU's internal driver chip. Fix: Replaced the airbag control module (matched the vehicle VIN and configuration codes), performed online programming, and cleared the fault.
Other Atto 8 Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.