UAE
AU
B177A

DTC B177A indicates the SRS (Supplemental Restraint System) control unit fails to detect the left middle-row (typically left second-row) seat belt pretensioner during self-diagnosis — Atto 8

Safety System

DTC B177A indicates the SRS (Supplemental Restraint System) control unit fails to detect the left middle-row (typically left second-row) seat belt pretensioner during self-diagnosis.

This is an open-circuit fault; the ECU detects infinite pretensioner circuit resistance or resistance outside the normal threshold (standard value: 1.5-2.5Ω).

The pretensioner is a key actuator in the passive safety system.

During a frontal collision, a pyrotechnic igniter instantly tightens the seat belt to eliminate slack between the occupant and the belt.

This fault indicates an open pretensioner circuit, preventing pretensioner deployment for this seat during a collision.

This condition may also disrupt the coordinated deployment logic of the same-side or related airbags. "Not present" in this fault code does not indicate a missing physical component; it designates an electrical "communication loss" or "open circuit".

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Song MAX left second-row seat rail worn through pretensioner wiring harness

✓
A 2019 BYD Song MAX DM with 42,000 km had the airbag warning light illuminated. Scanning revealed code B177A. Removing the left middle seat revealed the pre-tensioner wiring harness had chafed against the metal edge at the front of the seat rail, wearing through the insulation and completely severing all three copper cores. Replaced the pre-tensioner wiring harness assembly (part number: SA-585XXXX), added a rubber protective sleeve and cable ties at the contact point, and rerouted the wiring to prevent future abrasion. Cleared the fault codes and the system returned to normal.
BYD DTC AI Analysis

Tang DM pretensioner connector not connected after accident repair

✓
2021 BYD Tang DM. Following right-front collision repairs at a non-authorised workshop, the instrument cluster displayed a constant airbag warning light. Diagnosis revealed DTC B177A and a right-front impact sensor fault. Inspection found the left second-row seat had been removed for painting during the accident repair. Upon reinstallation, the technician had not fully seated the pretensioner connector, leaving it merely hanging on the clip and causing a loose connection. Reconnected the connector and confirmed the locking tab engaged. Performed 'Crash History Clear' and 'SRS System Reset' using a diagnostic tool. Fault resolved.
BYD DTC AI Analysis

Aftermarket second-row seat modification on Yuan EV dislodged the connector

✓
2019 BYD Yuan EV535. Owner self-installed a heating pad on the left middle row seat but didn't properly refit the trim panels afterward. Seat adjustment pulled the wiring, causing the pretensioner connector to come completely loose. Airbag warning light came on intermittently, particularly on rough roads. Found the connector partially detached with slight terminal oxidation. Fix: Cleaned the terminals, applied conductive grease, re-secured the connector and used cable ties to take up harness slack so seat movement wouldn't pull on the wires.
BYD DTC AI Analysis

BYD Song MAX Pretensioner Internal Open Circuit Replacement Case

✓
A 2019 Song MAX petrol with no accident history. The airbag warning light illuminated suddenly. Resistance measured infinite at the left second-row pre-tensioner connector. Disconnected the pre-tensioner; the body alone still measured infinite resistance, confirming the internal bridge wire had fractured. Replaced the genuine seatbelt assembly (including pre-tensioner, part number: SA-582XXXX). Fault cleared. Analysis suggests internal propellant moisture or long-term micro-vibration caused bridge wire fatigue. Sporadic component failure.
BYD DTC AI Analysis

Qin Pro SRS Control Unit Software Upgrade for False Alarm

✓
2020 Qin Pro developed intermittent B177A faults. Checked wiring harness and pretensioner resistance – both normal. Connectors normal. Consulted BYD TSB: confirmed early-batch SRS control unit (ACU) software calibration issue causes false middle-row pretensioner missing detection during low-temperature cold starts. Action: Upgraded ACU software to V3.2.1 or higher using VDS. No further faults after update.
Other Atto 8 Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.