UAE
AU
B17041B

DTC B17041B indicates the SRS (Supplemental Restraint System) ECU detected an open circuit or abnormal resistance in the left curtain shield airbag circuit (typically >4 — Qin Plus

Safety System

DTC B17041B indicates the SRS (Supplemental Restraint System) ECU detected an open circuit or abnormal resistance in the left curtain shield airbag circuit (typically >4.8Ω or <1.0Ω).

This fault indicates an interrupted electrical connection between the left curtain airbag inflator and the SRS control unit.

Causes include a disconnected connector, a wiring harness open circuit, or an internal open circuit within the curtain airbag assembly.

This condition prevents the left curtain airbag from deploying during a side impact or rollover event, severely compromising occupant head protection.

Because the SRS uses a dual-stage deployment circuit, this DTC typically triggers a circuit resistance warning.

Read the live data stream with a dedicated diagnostic tool to confirm the exact resistance value.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD E2 seat cover installation caused the left curtain airbag connector to detach.

✓
A 2019 BYD E2 came in with the airbag light on steady. Pulled code B17041B. The owner had recently had full-coverage seat covers fitted at a detailing shop. On tear‑down, we found the technician pulled the headliner harness when removing/installing the left front seat, loosening the yellow connector for the left curtain airbag—the secondary lock didn’t click. Reconnected the connector firmly and locked the CPA. Cleared codes, airbag light went out, resistance returned to 1.9 Ω. Recommendation: Disconnect the SRS system before removing or installing seats.
BYD DTC AI Analysis

Qin EV (flood damage): Left curtain airbag wiring harness corroded, open circuit

✓
2020 BYD Qin EV. The vehicle had previously flooded after wading through water deeper than the door sills. Following repairs, DTC B17041B set and would not clear. Removed the left front sill trim panel and found severe oxidation inside the intermediate connector joining the floor and headliner harnesses. The pins showed green copper corrosion. Checked continuity from this connector to the SRS ECU and measured over 10 ohms on one signal line (normal is under 0.5 ohms). Cut out the corroded section and re-crimped the terminals using waterproof heat-shrink tubing. Cleared the fault. Recommendation: When repairing flood-damaged vehicles, thoroughly inspect all airbag harness connectors and replace the complete harness assembly if necessary.
BYD DTC AI Analysis

E3: Internal open circuit in curtain airbag after accident repair

✓
BYD E3 sustained a side impact on the left. Replaced the left curtain airbag but DTC B17041B remained active. Measured the resistance of the new component with a multimeter; it showed infinite resistance, indicating a parts quality issue (improper storage or broken internal bridge wire). Replaced it with another genuine curtain airbag. The new part measured 2.1Ω. Installed it and cleared the fault. Curtain airbags are single-use components. Even if not deployed, severe vibration or dropping can damage the internal igniter. Always measure resistance before installation to confirm the component is serviceable.
BYD DTC AI Analysis

SRS ECU Software False Fault Report Upgrade Case

✓
Multiple 2019 Qin EVs intermittently set DTC B17041B during normal operation. Measured the curtain airbag resistance and wiring harness – both normal. Checked the BYD Technical Service Bulletin (TSB) and found that early-version SRS control software can falsely report open-circuit faults during voltage fluctuations (e.g., jump-starting after a flat battery). Upgraded the SRS ECU software using VDS2000 (from V1.02 to V1.05). The fault has not reoccurred since the upgrade. Recommendation: For intermittent faults with normal measurements, check the software version first.
BYD DTC AI Analysis

C-pillar trim clip pinched the wiring harness, causing an intermittent open circuit.

✓
The vehicle has no accident history, but the airbag warning light illuminated intermittently when driving over rough roads. The DTC retrieved was B17041B – intermittent fault. Removed the left C-pillar trim and found the wiring harness had been compressed by the trim clips over a long period, damaging the insulation and causing partial fracture of the internal copper strands. The circuit showed occasional continuity when tested statically but opened under vibration. Cut out the damaged section of the harness, re-routed it to avoid the sharp clip edges, and wrapped it with fleece tape. This permanently resolved the fault. Recommendation: When inspecting wiring, simulate vibration by lightly tugging the harness to test for continuity.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.