UAE
AU
B17A000

DTC B17A000 indicates the airbag control unit (SRS ECU) detected a logic error or hardware fault during its internal self-check — Qin Plus

Safety System

DTC B17A000 indicates the airbag control unit (SRS ECU) detected a logic error or hardware fault during its internal self-check.

Specifically, this fault indicates a failure in the ECU internal processor, memory (EEPROM/Flash), safety sensor, or power management module.

During the power-on self-test, the SRS ECU performs CRC checks and logic diagnostics on the internal accelerometer, crash algorithm logic area, backup power circuit, and CAN communication interface.

The ECU sets this code if it detects a data verification failure, RAM test failure, watchdog reset, or internal communication bus fault.

This is a functional safety fault that may cause the airbag system to enter fail-safe mode (disabling airbag deployment), fail to provide protection during a collision, or create a risk of unintended deployment.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Qin Pro DM supply voltage fluctuation causing intermittent ECU internal error

✓
A 2018 Qin Pro DM with 32,000 km showed intermittent "Check Airbag System" warnings on the instrument cluster. The scan tool retrieved history code B17A000. The fault occurred mostly during cold starts. Measuring the SRS ECU power terminals revealed the ignition voltage dropped to 7.2 V at startup—below the ECU operating threshold. Tracing the wiring found oxidation on the power connector between the ignition switch and ECU. Cleaning and tightening the connector and installing a voltage stabilizing capacitor per Technical Bulletin TB-2019-SRS-03 resolved the fault.
BYD DTC AI Analysis

Software bug in Qin Pro petrol version causes frequent internal error warnings

✓
2019 BYD Qin Pro (fuel). No collision history. SRS warning light on constantly, current fault code B17A000. Checked power and CAN lines—normal. BYD technical service bulletin confirms ECU software V1.02 on this batch has a memory management defect, triggering internal self-test errors between -5°C and 5°C. Fix: Upgraded to V1.05 using VDS2000. After upgrade, ran Write Configuration and Clear Codes. Light went out. One month follow-up—no recurrence.
BYD DTC AI Analysis

Water ingress caused SRS ECU internal short circuit

✓
2018 BYD Qin Pro DM. Airbag warning light stayed on after driving through floodwater. Read DTC B17A000; code would not clear. Found SRS ECU mounted beneath the floor. External waterproof cover was present, but the seal had deteriorated and allowed water inside. Internal PCB showed water stains and green corrosion. Measured internal power module shorted to ground. Replaced SRS ECU (part number 5A-3636100A), replaced waterproof seal, repositioned wiring harness waterproof boots, and configured and calibrated the new ECU. Fault cleared.
BYD DTC AI Analysis

Incorrect configuration after accident repairs caused internal error

✓
A crash-repaired 2019 Qin Pro DM displayed an SRS warning after replacing the airbag and wiring harness, logging DTC B17A000. The replacement ECU was a salvage unit with a mismatched VIN and incorrect seat occupancy sensor configuration for this model, causing internal validation failure. Ran the 'ECU Replacement' routine on a diagnostic scanner, rewrote the correct VIN and vehicle configuration codes ('1' = with side airbags, '2' = with curtain airbags, etc.), performed sensor calibration, and cleared the fault codes.
BYD DTC AI Analysis

False faults from flat battery after long-term storage

✓
2018 BYD Qin Pro (petrol). Parked for two months, the battery discharged severely (<8V). After a jump start, the SRS warning light remained constantly illuminated with DTC B17A000 stored. Diagnosis: The severe battery discharge caused the ECU memory test to fail during the power-on self-test. Repair: Replaced the ageing battery first, then cleared the fault codes with a diagnostic tool and performed the 'system self-test' routine. Once the ECU passed the power-on self-test after re-energising, the fault code did not return—a false fault. Advised the owner to disconnect the battery negative terminal or use a maintenance charger when storing the vehicle long-term.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.