UAE
AU
B16BF

DTC B16BF indicates an internal fault in the airbag electronic control unit (SRS ECU) or a system-level functional failure — Seal 6 EV

Safety System

DTC B16BF indicates an internal fault in the airbag electronic control unit (SRS ECU) or a system-level functional failure.

This fault involves an ECU internal processor self-check anomaly, memory checksum failure, power management module fault, or CAN communication interface fault.

The SRS ECU continuously monitors the internal operating voltage (3.3V/5V regulated output), EEPROM data integrity, watchdog timer status, and communication quality with the vehicle CAN network.

The system sets this DTC when the ECU detects an internal circuit fault, supply voltage outside the 9-16V range, excessive ground resistance (>1Ω), or CAN signal distortion.

This safety-critical fault may cause complete airbag system failure (airbags fail to deploy during a collision), unintended deployment, or seat belt pretensioner failure.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Tang DM-i Intermittent SRS ECU Reset Fault

✓
The instrument cluster intermittently displayed 'Check SRS System' with intermittent fault code B16BF. Technicians found the G101 ground point below the left A-pillar had a loose mounting bolt and an oxidised contact surface. After servicing the ground point, the fault remained. Further measurements revealed a poor connection in the power supply harness between the instrument panel distribution box and the SRS ECU near the steering column; voltage fluctuated between 8–12V when the harness was moved. Repairing the harness connector eliminated the fault. This case shows that unstable power supply is a common cause of B16BF.
BYD DTC AI Analysis

BYD Yuan EV SRS ECU internal memory damaged

✓
Customer reported the airbag warning light staying on. Scan tool showed code B16BF, which could not be cleared. Power supply, ground, and CAN bus all normal. A software refresh attempt displayed 'ECU not responding' on the scan tool. Removed the SRS ECU (located beneath the gear selector) and found electrolytic capacitor leakage on the circuit board that had corroded the solder joints of a nearby EEPROM chip. Installed a new SRS ECU, then performed online configuration and impact sensor calibration (using VDS2000, selecting 'Yuan EV' model menu). Fault resolved.
BYD DTC AI Analysis

CAN bus interference in BYD Qin Pro DM caused B16BF

✓
After a minor collision, the front bumper was replaced. Fault code B16BF then appeared. We found the front impact sensor wiring harness had been pinched during installation, causing an intermittent short between the CAN-H line and the body. Although the sensor itself was not faulty, the surge voltage from the short circuit triggered a protective lockout of the SRS ECU communication interface. We repaired the wiring harness insulation, cleared the code, and the system returned to normal. This case shows the need to check wiring harness integrity after collision repairs.
BYD DTC AI Analysis

BYD Song MAX software version defect

✓
Early model Song MAX vehicles (2019 MY) built before the batch recall exhibited B16BF faults. A BYD technical bulletin confirmed this as an ECU software bug: during cold starts below -10°C, a timing error in the ECU self-diagnostic routine caused false fault reports. The fix: flash the ECU to the latest software using VDS2000 (version suffix must be greater than V2.3.1), then perform sensor recalibration. Three months of monitoring after the flash showed no further faults.
BYD DTC AI Analysis

SRS fault caused by aftermarket modification to BYD Han EV

✓
During installation of a 360-degree surround view camera system, the installer mistakenly connected the reversing light power wire to the SRS ECU IGN power supply line, causing ECU supply voltage fluctuations. This triggered DTC B16BF and multiple sensor communication faults. Inspection found the modified wiring had damaged the original harness insulation, and the SRS ECU fuse holder was burned. Repaired the original harness, removed the unauthorised wiring, and replaced the fuse holder and SRS ECU (overvoltage had damaged the internal voltage regulator module). Fault resolved.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.