UAE
AU
B2AB9-97

DTC B2AB9-97 indicates an internal fault or performance abnormality in the passenger seat Occupant Classification System (OCS) sensor, not "air conditioning load too high" as stated in the original information — Seal 6 EV

Thermal Management System

DTC B2AB9-97 indicates an internal fault or performance abnormality in the passenger seat Occupant Classification System (OCS) sensor, not "air conditioning load too high" as stated in the original information.

Integrated into the front passenger seat cushion, the sensor uses pressure-sensitive elements to detect seat occupancy and passenger weight range.

It outputs an analogue voltage signal to the airbag control unit (SRS ECU) (normal range 2.5V-3.5V, varying with weight).

The ECU sets this code upon detecting a fixed sensor signal voltage, a voltage outside the valid range, or an open or short circuit exceeding the threshold.

This fault forcibly disables the front passenger airbag (the instrument cluster displays "PASS AIR BAG OFF") or prevents the system from adjusting the deployment strategy based on passenger weight during a collision.

This severely compromises passive safety system operation and requires immediate repair.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin Plus DM-i (2021) - Sensor unit damaged

✓
**Symptoms**: After starting the vehicle, the airbag warning light on the dashboard stays on. The passenger airbag displays "OFF" regardless of front passenger seat occupancy. **Diagnosis**: Connected VDS2000 and read the SRS data stream. The passenger-side OCS sensor output voltage remained constant at 0.2V (normal: varies between 2.5V–3.5V with pressure). Removed and inspected the yellow connector beneath the seat—no looseness or water ingress. Measured harness supply voltage (12V) and ground—both normal. Determined the sensor's internal pressure-sensitive element was damaged. **Solution**: Replaced the front passenger seat occupant sensor assembly (integrated in the seat cushion foam). Performed "OCS zero calibration" and "weight learning" after replacement (path: SRS system → Special functions → Seat occupant sensor calibration). Cleared fault codes after calibration. System returned to normal occupancy recognition.
Original source ↗
BYD DTC AI Analysis

BYD Song Pro DM (2022) - Poor Contact in Wiring Harness Connector

✓
Symptoms: After interior cleaning, the airbag warning light came on intermittently and sometimes went out on bumpy roads. DTC B2AB9-97 was intermittent. Diagnosis: Inspected the wiring harness under the front passenger seat. Found the OCS sensor harness plug interfered with the seat rail during fore-aft adjustment. The plug locking clip was broken and the pins had poor contact. Tugging during cleaning worsened the contact. Voltage at the sensor plug dropped out when the harness was wiggled. Solution: Repaired the harness plug, replaced the damaged plug housing, re-crimped the harness terminals, and secured the harness to the seat frame with cable ties, routing it away from the rail. Cleared the DTC and tested with multiple seat adjustments; the fault did not recur.
Original source ↗
BYD DTC AI Analysis

BYD Han EV (2020) - Sensor damage from water ingress

✓
Symptoms: Airbag warning light illuminated after driving in heavy rain or through deep water. DTC B2AB9-97 stored. Front passenger seat had been covered with wet clothing for an extended period. Diagnosis: Removed and inspected front passenger seat. Found water stains at OCS sensor housing seal; internal circuit board oxidised. Liquid penetrated seat fabric into sensor, causing signal drift. Measured sensor resistance out of spec (normal ~1.5–3 kΩ). Fix: Replaced front passenger seat cushion assembly (OCS sensor and cushion are highly integrated; separate replacement cannot guarantee sealing). Checked seat foam for moisture and replaced damaged sections. Calibrated OCS system after installation. Added waterproof breathable membrane above sensor for extra protection.
Original source ↗
BYD DTC AI Analysis

BYD Tang DM-p (2023 model) — Software program and calibration lost

✓
Symptoms: After OTA or multimedia system update, airbag warning light suddenly lit with DTC B2AB9-97. No accident or seat removal history. Diagnosis: Scanned with latest diagnostic tool. Found SRS control unit software version incompatible with OCS sensor hardware communication protocol, or seat occupant sensor calibration data lost during upgrade. Physical wiring and sensor appearance checked normal. Software logic error. Resolution: Reflashed SRS (airbag control unit) with latest software and performed complete OCS system configuration and calibration (zero-load and loaded). Some cases also require OCS sensor firmware upgrade. Cleared fault codes after programming. System normal.
Original source ↗
BYD DTC AI Analysis

BYD Seal (2022) - Configuration error after accident repair

✓
Symptoms: Front-end collision. After replacing the front bumper, airbags and other components, the airbag warning light came on at post-repair delivery. Retrieved DTC B2AB9-97: passenger airbag disabled. Diagnosis: Removed and reinstalled the passenger seat during collision repair. The sensor connector was secure, but the OCS sensor serial number or configuration parameters in the SRS control unit did not match the vehicle (possible causes: replacement seat assembly from a different batch, or incorrect data write to the control unit). The diagnostic tool displayed 'OCS not configured' or 'Configuration error'. Solution: Used the diagnostic tool to access the SRS system → Programming/Configuration, and rewrote the correct OCS sensor ID code (manually input the barcode from the sensor label or performed automatic recognition). After completing the configuration, ran the 'System Learn' or 'Calibration' procedure so the control unit recognizes the new sensor. Cleared the fault codes; the airbag warning light went out and the collision recovery system returned to normal.
Original source ↗
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.