UAE
AU
B169A

DTC B169A indicates the airbag control unit (SRS ECU) detects an internal system fault or critical function failure — Seal U

Safety System

DTC B169A indicates the airbag control unit (SRS ECU) detects an internal system fault or critical function failure.

This fault code typically indicates an abnormality in the ECU internal processor, memory, or power management module, forcing the airbag system into a degraded mode or complete failure state.

Specific symptoms include crash detection algorithm failure, ignition loop driver circuit faults, or interrupted communication with other safety modules (such as seatbelt pretensioners and crash sensors).

This fault directly prevents airbag deployment during a collision, disables seatbelt pretensioners, and continuously illuminates the instrument cluster airbag warning light.

On some models, this fault restricts Child Presence Detection (CPD) and smart key system functions, as these systems share sensor data or communication buses.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

2021 BYD Tang DM SRS ECU internal chip fault

✓
The dashboard displayed 'Check Airbag System'. Retrieved DTC B169A-00 (active). Inspection confirmed no accident history, but the vehicle had waded through water up to sill level. Removed the SRS ECU (located under the centre console) and found traces of oxidation on the circuit board. Replaced the ECU, but the fault persisted. Further inspection revealed both old and new ECUs could not communicate with the right-side impact sensor via the LIN bus. Found an internal short in the sensor causing a protective lockout in the ECU. Replaced the right B-pillar impact sensor and reconfigured the ECU. The fault cleared. Key point: B169A may be the result rather than the cause; inspect all peripheral devices.
BYD DTC AI Analysis

BYD Yuan EV 2019: Aftermarket equipment installation causing CAN bus interference

✓
Owner reported the airbag warning light occasionally flashing while driving. The diagnostic tool retrieved an intermittent B169A fault code. Inspection found the owner had installed an aftermarket dashcam powered from the SRS fuse. During startup, the device caused a voltage drop (to 8.5 V), resetting the SRS ECU. After removing the aftermarket device, rewiring the power feed to the ACC circuit, and using an oscilloscope to confirm no abnormal interference on the CAN bus, the fault did not return. Recommendation: Never tap power from SRS system circuits.
BYD DTC AI Analysis

BYD Qin Pro 2020 – Software Version Defect

✓
After accident repairs (replaced front bumper and left front sensor), the instrument cluster kept showing DTC B169A and the code would not clear. Found the replacement crash sensor was part number 5A-3636100 (Yuan EV specific), which had firmware incompatible with the required part number 5A-3636100B for the Qin Pro. After installing the correct part, the fault persisted. Ultimately, a BYD Technical Service Bulletin (TSB) confirmed that this batch of vehicles requires an SRS ECU software upgrade to version V2.3 to resolve the compatibility issue. After the upgrade, performed sensor ID registration and configuration write—the fault was resolved.
BYD DTC AI Analysis

2019 BYD Song MAX: Bad ground caused ECU reset

✓
The airbag warning light illuminated while driving on rough roads. Diagnosis revealed stored DTC B169A. Measured 0.8V voltage drop at SRS ECU ground terminal G102 (normal: less than 0.1V). Inspection found the ground point below the left A-pillar with a loose mounting bolt and paint on the contact surface. Sanded the metal surface at the ground point, re-tightened the bolt, and applied conductive grease. After a 200 km road test, the fault did not recur. Analysis: Poor grounding caused momentary power loss to the ECU during vibration, triggering internal fault protection.
BYD DTC AI Analysis

2020 BYD Han EV: Lockout due to uncleared accident data

✓
The vehicle had a minor rear-end collision. The airbags did not deploy, but DTCs B169A and B1650 (collision data stored) were retrieved. After the accident repairs, the fault codes could not be cleared. According to the BYD workshop manual, the SRS ECU may enter a locked state after recording a collision event, even without deployment. Using a diagnostic scan tool, the 'Crash Data Reset' and 'ECU Unlock' special functions were performed. After entering the manufacturer authorization code, the fault codes were successfully cleared and the system returned to normal. Note: This operation requires manufacturer authorization and confirmation that the ECU hardware has no physical damage.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.