UAE
AU
C001100

DTC C001100 indicates a malfunction in the drive circuit of the internal left front wheel outlet solenoid valve within the Integrated Power Brake (IPB) system — Seal U

Braking System

DTC C001100 indicates a malfunction in the drive circuit of the internal left front wheel outlet solenoid valve within the Integrated Power Brake (IPB) system.

This solenoid valve returns high-pressure brake fluid from the left front wheel brake cylinder to the reservoir during ABS/ESP activation to release wheel cylinder pressure.

A "drive fault" indicates the IPB ECU detects an open circuit, short circuit, or short to ground or power in the H-bridge circuit driving this solenoid valve, or it detects a drive current exceeding the calibrated threshold (typically 2-3A).

This fault prevents independent pressure release at the left front wheel, affecting ABS, ESC, AUTOHOLD, and Automatic Emergency Braking (AEB) functions.

The IPB enters a degraded mode, retaining conventional hydraulic braking while potentially limiting electronic brake assist.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Song PLUS DM-i: IPB internal solenoid coil open circuit

✓
At 80,000 km the ABS and ESC warning lights illuminated. Read DTC C001100 (current fault). Checked the IPB connector — no issues. Measured infinite resistance at the left front outlet valve (normal ~3.5 Ω), indicating an open circuit in the IPB internal solenoid coil. Replaced the IPB assembly and performed bleed and calibration; fault resolved. Root cause: coil fatigue fracture from long-term high-frequency solenoid operation.
BYD DTC AI Analysis

IPB Drive Circuit Corrosion Case After Water Wading

✓
Dashboard displayed "Braking System Fault" after driving through water. Retrieved DTCs C001100/C001104 (left front outlet/inlet valve drive fault). Disassembly revealed water inside the IPB connector; oxidised pins caused a short in the drive circuit. Fault persisted after cleaning and drying the connector. Internal IPB drive chip measured as burned out. Replaced IPB assembly and reinforced connector waterproofing.
BYD DTC AI Analysis

Software false positive caused intermittent C001100 fault.

✓
2021 Song PLUS DM-i. Customer reported occasional ABS warning light illumination during high-speed driving; the light extinguished after ignition-off. Diagnostic tool logged C001100 as a historical fault. Freeze frame data showed the vehicle was on rough road surfaces when the fault occurred. Wiring harness inspection found no damage. Solenoid valve resistance measured normal. TSB review revealed early IPB software had an overly strict solenoid valve drive current threshold calibration. Upgraded IPB software to V2.3. One-month follow-up showed no recurrence.
BYD DTC AI Analysis

Brake fluid contamination caused valve spool sticking

✓
One week after service, fault code C001100 appeared. Inspection found non-genuine brake fluid (incorrect DOT 4 specification) that was black and contaminated. IPB disassembly revealed the left front outlet valve spool stuck in the open position, causing continuous drive current overload; the ECU logged a protective fault. Replaced the IPB assembly, thoroughly flushed the brake lines, and filled with genuine DOT 4 LV brake fluid. Fault resolved.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.