UAE
AU
U014008

DTC U014008 indicates a CAN data communication integrity check failure between the ABS/ESC control unit and the vehicle gateway controller — Seal U

Braking System

DTC U014008 indicates a CAN data communication integrity check failure between the ABS/ESC control unit and the vehicle gateway controller.

Data frames sent by the ABS module to the gateway over the Powertrain CAN bus contain CRC errors, out-of-sequence frames, abnormal Data Length Codes (DLC), or protocol format mismatches.

Consequently, the gateway determines the received brake system status data is corrupted.

This fault triggers the brake system fail-safe strategy, degrading or completely disabling functions such as ABS, ESC, EBD, and Autonomous Emergency Braking (AEB).

Simultaneously, the gateway sends multi-system fault warnings to the instrument cluster, severely compromising driving safety.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

2018 BYD E5 – Gateway module water ingress corrosion caused data validation failure

✓
2018 E5, 80,000 km. ABS and ESC warning lights illuminated after driving in rain. Fault code U014008. The gateway controller, mounted under the left side of the dashboard, had water ingress from a perished windscreen seal that corroded the circuit board. CAN bus voltage between the gateway and ABS measured normal, but the internal CAN transceiver chip (TJA1043) output distorted waveforms. Replaced the gateway controller and sealed it; also replaced the windscreen seal to prevent recurrence. Fault resolved.
BYD DTC AI Analysis

E5 ABS pump assembly CAN chip damaged, continuously transmitting error frames

✓
The vehicle failed to engage high voltage; the instrument cluster displayed a brake system fault. The scanner read DTC U014008, which would not clear. Power and ground at the ABS module were normal, but scoping the ABS-side CAN bus revealed heavy error frames. Removed and disassembled the ABS pump assembly; the internal CAN transceiver chip was damaged from overvoltage, continuously transmitting malformed packets and causing the gateway to flag the data as corrupt. Replaced the ABS/ESC assembly and performed calibration. Fault resolved.
BYD DTC AI Analysis

Wiring harness chafing caused a CAN-H short to ground, resulting in an intermittent fault.

✓
ABS warning light occasionally illuminated when driving on rough roads; normal on smooth surfaces. Read DTC U014008 (intermittent). Inspection found ABS wiring harness in engine bay rubbing against engine mount, with worn insulation causing intermittent CAN-H short-to-ground. When shorted, ABS data signals pulled low, resulting in CRC checksum failures on packets received by gateway; data flagged as corrupt. Re-routed harness and fitted protective sleeving, insulated worn sections. Fault eliminated.
BYD DTC AI Analysis

Software version mismatch caused protocol parsing error

✓
A 2019 E5 repaired after an accident kept setting U014008 after a second-hand ABS pump was installed. Check showed the replacement was an early hardware revision with software calibration incompatible with the vehicle gateway protocol (data frame length definition mismatch). Hardware part numbers matched, but the software was too old (V2.3). Flashed the ABS module to V2.9; the protocols aligned, the fault code cleared automatically, and all braking functions returned to normal.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.