UK
AU
B165400

DTC B165400 indicates the airbag control unit (SRS ECU) detects a communication interruption with the Left Front Impact Sensor during a self-test or drive cycle — Atto 3

Safety System

DTC B165400 indicates the airbag control unit (SRS ECU) detects a communication interruption with the Left Front Impact Sensor during a self-test or drive cycle.

This sensor typically mounts on the left front longitudinal member (inside the fender or near the headlamp bracket) and detects front collision acceleration signals. "Not connected" indicates a disconnected physical plug, an open circuit in the sensor power/ground wiring, an open CAN/LIN communication line, an internal sensor open circuit, or a poor connection at the ECU connector.

An active fault forces the SRS system into a degraded mode.

This condition may prevent the left front airbag, driver airbag, or seatbelt pretensioner from deploying correctly during a collision, and illuminates the instrument cluster airbag warning light (flashing or solid).

4
Cases Logged
Real-World Cases
BYD DTC AI AnalysisFrom Chinese market (translated)

Qin Pro DM airbag warning light stays on after accident repair

✓
A 2019 BYD Qin Pro DM had its front bumper and left headlight replaced at a repair shop after a minor front collision. Afterwards, the airbag warning light on the instrument panel stayed on constantly. The stored DTC was B165400 (current). Inspection found the collision sensor connector on the left front side member was not fully seated and its locking tab had broken. The repair shop technician, unfamiliar with the BYD SRS system, pulled on the wiring harness while fitting the bumper, causing the connector to come loose. Replaced the wiring harness connector (with harness assembly), reconnected the sensor, cleared the fault codes, and performed a VDS system self-test. Fault resolved.
BYD DTC AI AnalysisFrom Chinese market (translated)

BYD E2 left front sensor communication fault after water ingress

✓
2020 E2 EV. After driving through floodwater during heavy rain, the airbag warning light illuminated. The scanner logged DTCs B165400 and B165500 (right front) simultaneously. Inspection found damage to the wiring harness protective sleeve beneath the left front chassis rail in the front compartment. Water ingress corroded the sensor connector; the oxidized pins produced green copper deposits. Cleaned the connector with WD-40 precision electrical contact cleaner. Wiring harness continuity tested normal, but the sensor internals had short-circuited due to moisture. Replaced the left front impact sensor and waterproofed the harness using heat shrink tubing and waterproof sealant. Fault rectified. Warning: EV wading depth must never exceed half the tyre height.
BYD DTC AI AnalysisFrom Chinese market (translated)

Qin EV sensor wiring harness underbody scrape wear causes intermittent fault.

✓
2019 BYD Qin EV. The owner reported the airbag warning light illuminated intermittently, especially on rough roads. DTC B165400 was an intermittent historical fault. We raised the vehicle and inspected the airbag crash sensor wiring harness beneath the left front longitudinal rail. Where the harness passes through the rail opening, an underbody impact had worn through the protective sleeve. Only 2–3 copper strands remained connecting the wires, causing intermittent electrical contact while driving. We cut out the damaged harness section, crimped new waterproof terminals, insulated with double-layer heat shrink tubing, and re-routed the harness to prevent chafing against the rail edge. The fault did not return.
BYD DTC AI AnalysisFrom Chinese market (translated)

E3 front radar installation incorrectly modified collision sensor wiring

✓
2020 E3. After the customer had front parking sensors installed at an external workshop, the airbag warning light stayed on continuously when starting the vehicle. DTC B165400. Inspection found the retrofit shop mistakenly tapped into the left front collision sensor wiring harness, thinking it was the radar power wire. This caused a short circuit in the sensor circuit, and the SRS ECU protectively disabled that channel. Repaired the wiring harness (removed the wire taps, soldered the wires, and sealed with heat-shrink tubing). Replaced the damaged collision sensor (internally shorted). Recoded the SRS ECU to unlock the channel (the ECU had locked it after detecting the short). Fault resolved. Advised the customer to have accessories fitted at an authorised dealer.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.