UK
AU
B167100

The Right Side Impact Sensor is a key safety component of the Supplemental Restraint System (SRS) — Atto 3

Safety System

The Right Side Impact Sensor is a key safety component of the Supplemental Restraint System (SRS).

The sensor typically mounts in the right B-pillar, right front door, or right C-pillar.

It monitors acceleration changes on the right side of the vehicle.

Upon detecting severe deceleration from a side impact, the sensor sends a crash signal to the SRS control unit to trigger the right side airbag and/or side curtain airbag deployment.

DTC B167100 indicates the SRS control module fails to receive a valid signal from the Right Side Impact Sensor, or the received signal falls out of range (including open circuit, short circuit, signal distortion, or no sensor response).

This fault disables the right side impact protection function.

The airbags may fail to deploy during a side collision.

The system illuminates the airbag warning light to alert the driver of a safety system fault.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Side impact sensor mounting bracket deformation caused signal fault on Qin Pro DM

✓
Symptoms: Airbag warning light suddenly illuminated during normal driving with no collision history. Diagnosis: Connected a scan tool and retrieved DTCs B168000 (left side) and B167100 (right side). Inspected the impact sensors at the corresponding fender liners; found no visible damage. Measured sensor supply voltage at 12V (normal), ground (normal), and CAN line voltage (normal). Replaced the sensor but the fault persisted. Eventually discovered the sensor mounting bracket had deformed due to a previous improper accident repair, causing the sensor installation angle to shift and affecting signal detection. Resolution: Straightened the impact sensor mounting bracket, ensured the sensor installation angle met specifications (vertical deviation <5°), and retightened the fasteners. Fault resolved.
Original source ↗
BYD DTC AI Analysis

BYD Dolphin B167100 Occupant Detection System Calibration Failure Case

✓
Symptom: After an OTA update, the front passenger seatbelt warning malfunctioned — it alerted when unoccupied but remained silent when occupied. DTC B167100 stored. Diagnosis: The dealership scan tool found DTC B167100 stored in the Body Control Module. The front passenger pressure sensor and capacitive sensor operated normally. The workshop manual identified this code as 'occupant detection system calibration data error'. Analysis indicated a data validation failure in the Body Control Module during the OTA update. Resolution: Used the VDS diagnostic tool to perform the 'occupant detection system recalibration' procedure, entering a standard weight of 75 kg for calibration learning. Cleared the fault code after completion, and the function returned to normal.
BYD DTC AI Analysis

BYD Tang DM B16 Series Seatbelt Pretensioner Wiring Harness Poor Contact

✓
Symptoms: On starting the vehicle, the dashboard displayed "Check SRS System". The seatbelt warning light flashed and an intermittent buzzer alarm sounded. Read DTC B167000. Diagnosis: Connected a diagnostic tool to read the airbag system fault codes and found a B-pillar seatbelt pretensioner circuit fault. Removed the B-pillar trim to inspect the seatbelt pretensioner connector and found corrosion on the terminals. Measured pretensioner resistance: 2.8Ω (normal 2.0–3.0Ω). Resistance normal. Confirmed loose connector pins caused poor contact. Solution: Cleaned the seatbelt pretensioner connector, adjusted pin tension, applied conductive grease and reconnected the plug. Fault cleared.
BYD DTC AI Analysis

BYD Song MAX: Replaced damaged Occupant Detection Sensor (ODS) unit

✓
Symptoms: Airbag warning light on instrument panel stays on. When a passenger occupies the front passenger seat, the airbag indicator does not change status. The front passenger airbag may fail to deploy correctly during a collision. B169000 series DTCs stored. Diagnosis: Scanned with VDS diagnostic tool and found B16 series DTCs. Checked the Occupant Detection Sensor (ODS) connector beneath the front passenger seat. Measured sensor resistance and found it outside specification (normal: 2.5-3.5kΩ, measured: 0.8kΩ). Inspected the wiring harness and found no shorts or open circuits. Determined internal sensor failure. Resolution: Replaced the front passenger seat Occupant Detection Sensor (ODS sensor). Recalibrated the occupant classification system. Cleared DTCs and tested normal.
Original source ↗
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.