UK
AU
B170F-00

DTC B170F-00 indicates a short to power fault in the driver seat Occupant Sensing System (OSS) — Atto 3

Safety System

DTC B170F-00 indicates a short to power fault in the driver seat Occupant Sensing System (OSS).

Integrated into the driver seat cushion, the sensor uses a pressure sensing mat and an electronic control module to detect seat occupancy.

It sends a 0.4-4.6V analog voltage signal to the SRS airbag control unit (approximately 0.5V when unoccupied and 4.2V when occupied).

The SRS module sets this DTC when it detects a continuous voltage above 4.8V or near battery voltage.

This occurs if the signal circuit shorts to the 12V power supply line (B+), the internal sensor circuit breaks down, or the control module fails.

This fault forces the SRS system into fail-safe mode: the driver airbag may fail to deploy, the seat belt reminder function may malfunction (false or missing warnings), and the instrument cluster airbag warning light remains illuminated.

Because this fault affects the passive safety system, do not drive the vehicle until repaired.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

After replacing seats with aftermarket units on a Song Plus DM-i, the airbag warning light stays on.

✓
After the owner replaced the driver's seat at a third-party workshop with a non-genuine unit, the airbag warning light stayed on and the driver's seatbelt reminder stopped working. VDS scan retrieved DTC B170F-00. Measured the occupancy sensor in the new seat: resistance only 0.8kΩ (OEM specification 2.5–3.5kΩ). The aftermarket sensor's incompatible spec caused abnormal signal voltage. Replaced the sensor with a genuine driver's seat occupancy sensor, then ran sensor calibration and SRS configuration writing. Fault codes cleared; system returned to normal.
Original source ↗
BYD DTC AI Analysis

Seat sensor short circuit in Qin Plus EV after water wading

✓
After driving through standing water approximately 30cm deep, the instrument cluster displayed 'Check Airbag System' and the driver's seat heating failed. Retrieved DTCs B170F-00 and U0151. Removed the seat and found water accumulation on the inner side of the seat rails, oxidation and corrosion on the occupancy sensor control module pins, and measured a short to ground on the signal wire. Replaced the seat occupancy sensor assembly, removed water from the seat foam and dried it, then applied waterproof sealant at the sensor mounting location. Performed system calibration after the repair. Fault resolved.
Original source ↗
BYD DTC AI Analysis

Han EV seat adjustment causing wiring harness wear, resulting in intermittent fault

✓
While driving, the instrument cluster occasionally showed an airbag fault warning that cleared after stopping and restarting. The driver's seat belt reminder also worked intermittently. Stored DTCs revealed an intermittent B170F-00. Inspection found that the occupant sensor wiring harness rubbed against the seat rail during fore-aft adjustment, damaging the insulation and causing occasional shorting to the power wire. Repaired the damaged wiring (re-soldered and re-wrapped). Rerouted the harness and secured it to the seat frame. Fitted a wiring protection sleeve to prevent contact with moving parts. Two weeks of follow-up: no recurrence.
Original source ↗
BYD DTC AI Analysis

Sensor calibration data lost on new Tang DM-p

✓
One week after delivery of the new vehicle, it frequently triggered false 'person in vehicle' warnings after locking when unoccupied, or displayed 'no person in vehicle' when occupied. Read DTCs B170F-00 and B1710-00. Inspected sensor—no physical damage, but scan tool showed sensor output voltage fixed at 2.0 V (not changing with occupancy). Determined cause: severe vibration during transport or battery disconnection caused calibration data loss. Performed 'seat occupancy sensor zero-point calibration' and 'sensitivity learning' using scan tool. No parts replaced; fault resolved.
Original source ↗
BYD DTC AI Analysis

Destroyer 05 loose connector fault after service

✓
The airbag warning light came on after routine maintenance (including interior cleaning). The owner reported the seats had been removed during this service. We read DTC B170F-00. We checked the wiring harness under the seat and found the 4-pin occupancy sensor connector was not fully seated (locking tab not engaged). This caused poor contact at the signal pin and intermittent contact with the adjacent power pin. We reseated the connector, ensured the locking tab engaged, cleared the DTC, and tested the system with and without an occupant. The system returned to normal.
Original source ↗
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.