UK
AU
B175C-00

DTC B175C-00 indicates the airbag control unit (SRS ECU) detects resistance in the Right Rear Side Airbag ignition circuit above the calibrated threshold — Atto 3

Safety System

DTC B175C-00 indicates the airbag control unit (SRS ECU) detects resistance in the Right Rear Side Airbag ignition circuit above the calibrated threshold.

Normal airbag igniter resistance ranges from 1.6Ω to 2.4Ω (standard value approximately 2.0Ω).

The ECU sets this fault when it detects resistance exceeding approximately 2.8Ω or a high-resistance state in the circuit.

This fault indicates poor contact or a partial open in the ignition circuit, or abnormal internal resistance in the airbag module.

As a functional fault in the passive safety system, it may prevent the side airbag from deploying during a collision.

Because the SRS uses a two-stage diagnostic mechanism, this fault code continuously illuminates the airbag warning lamp and may force the entire airbag system into a downgraded protection mode, even if the vehicle remains drivable.

3
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin Pro right rear side airbag connector oxidized, causing high resistance

✓
Symptom: Airbag warning light stays on. Scanner shows DTC B175C-00. No collision history; fault appeared suddenly. Diagnosis: Disconnected the battery and checked the right rear seat side airbag connector. Measured airbag harness terminal resistance to ground: >1MΩ (normal). Voltage to ground: <1V (normal). Measured resistance between K08-2 (Y/B) and K71-17 (harness between airbag module and ECU): >1Ω (abnormal). Found the harness connector inside the right rear sill trim oxidised and loose. Fix: Cleaned the oxidised terminals and applied conductive grease. Re-secured the connector. Cleared the fault codes and cycled the ignition multiple times. Fault resolved.
Original source ↗
BYD DTC AI Analysis

BYD Song Pro DM rear side airbag wiring harness chafing causing intermittent warning

✓
Symptom: Airbag warning light illuminates intermittently, particularly over rough surfaces. Stored DTC: B175C-00. Diagnosis: Found the RH rear seat side airbag connector not fully locked. Reconnected and cleared the DTC, but the fault returned two days later. Further inspection revealed chafing damage to the harness at the seat rail, causing intermittent high resistance. Measuring resistance at the airbag module while moving the harness showed fluctuation between 2.8Ω and 5.2Ω (specification: 2Ω±0.4Ω). Resolution: Replaced the RH rear seat side airbag wiring harness assembly. Adjusted the harness routing to avoid the seat rail and secured it with cable ties, ensuring adequate movement allowance. Cleared the DTCs and road tested; no recurrence.
Original source ↗
BYD DTC AI Analysis

Replaced right rear side airbag on BYD Tang II; fault persists

✓
Symptoms: Airbag warning light stayed on with DTC B175C-00 after right rear door body repair and removal of right rear seat. Shop replaced right rear side airbag module but fault remained. Diagnosis: New airbag module resistance measured 2.1Ω (normal). Checked harness between airbag ECU and module: K08-1 (Y/R) to K71-18 measured 0.8Ω (normal), but K08-2 (Y/B) to K71-17 measured 3.5Ω (high). Found right B-pillar lower connector had water ingress during previous repair, causing pin oxidation. Resolution: Replaced right B-pillar lower SRS harness connector, dried harness and applied waterproof sealant. Reconnected, cleared codes, and cycled ignition multiple times to confirm fix.
Original source ↗
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.